6. What message is issued by a neighbor as a response to a valid Open?
A. Keepalive
B. Open
C. Exchange
D. NotificationE. Ping
Answer: A
7. Which of the following is not exchanged in a BGP Open message?
A. BGP version number
B. The local AS number
C. The hold time
D. The keepalive timer
E. The Router ID
Answer: D
8. The state of one BGP neighbor shows Established, which of the following is false?
A. The router has established a complete session with that neighbor.
B. BGP can exchange update, notification and keepalive messages with that neighbor
C. If the keepalive timer expires, the local system sends a keepalive message and restarts its keepalive timer
D. If the local system receives a notification message, it changes its state to OpenConfirmE. Established is the operational state
Answer: D
9. Which of the following is a Well Known Mandatory attribute?
A. Origin Code
B. Local Preference
C. MED
D. AS PathE. (a) and (d)
F. (b) and (d)
Answer: E
10. Which of the following is true, based on the AS Path list shown here?65206 65111 65100
A. AS 65206 originated the route
B. AS 65111 is a transit AS
C. AS 65100 is a transit AS
D. AS 65100 originated the route
E. (b) and (d)F. (a) and (c)
Answer: E
更多最新考试信息可登陆www.pass4side.cn网站查看！本文考试题库摘自pass4side.cn 更新时间：2008-9-10
2008年9月24日星期三
Pass4side 4A0-102 考试题库(1-5)
1. Which of the following are Link State protocols?
A. BGP
B. RIP
C. OSPF
D. IS-IS
Answer: CD
2. ECMP supports which of the following. Choose the best answer.
A. 8 equal-cost paths per destination learned from any protocol
B. 16 equal-cost paths per destination learned from any protocol
C. 8 equal-cost paths per destination learned from the same protocol and preference
D. 16 equal-cost paths per destination learned from the same protocol and preference
E. 4 equal-cost paths per destination
Answer: D
3. Which of the following statements best describes the function of the RTM?
A. From the router’s route table, select the best routes to be installed in the FIB for forwarding data.
B. Based on the metrics of the routing protocol, chose the lowest cost route to be installed in the route table.
C. Apply the BGP route selection criteria to select the best route to be installed in the route table.
D. Select the preferred route from the various routing protocols to be installed as the active route in the routetable.
E. Apply the assigned import and export policies to determine the routes to be advertised to the router’s neighbors.
Answer: D
4. What items are carried in a typical classless routing update? Select the best answer.
A. network address, mask and metric
B. network address and metric
C. prefix and mask
D. prefix, next-hop and metric
E. prefix and next-hop
Answer: A
5. Choose the most accurate statement about the connections between eBGP peers.
A. eBGP peers are usually directly connected to each other.
B. eBGP peers are always directly connected to each other.
C. eBGP peers are never directly connected to each other.
D. eBGP peers are usually directly connected to each other, unless they are in the same autonomous system.
E. eBGP peers are usually not directly connected to each other, additional configuration is required if they are.
Answer: A
更多最新考试信息可登陆www.pass4side.cn网站查看！本文考试题库摘自pass4side.cn 更新时间：2008-9-10
A. BGP
B. RIP
C. OSPF
D. IS-IS
Answer: CD
2. ECMP supports which of the following. Choose the best answer.
A. 8 equal-cost paths per destination learned from any protocol
B. 16 equal-cost paths per destination learned from any protocol
C. 8 equal-cost paths per destination learned from the same protocol and preference
D. 16 equal-cost paths per destination learned from the same protocol and preference
E. 4 equal-cost paths per destination
Answer: D
3. Which of the following statements best describes the function of the RTM?
A. From the router’s route table, select the best routes to be installed in the FIB for forwarding data.
B. Based on the metrics of the routing protocol, chose the lowest cost route to be installed in the route table.
C. Apply the BGP route selection criteria to select the best route to be installed in the route table.
D. Select the preferred route from the various routing protocols to be installed as the active route in the routetable.
E. Apply the assigned import and export policies to determine the routes to be advertised to the router’s neighbors.
Answer: D
4. What items are carried in a typical classless routing update? Select the best answer.
A. network address, mask and metric
B. network address and metric
C. prefix and mask
D. prefix, next-hop and metric
E. prefix and next-hop
Answer: A
5. Choose the most accurate statement about the connections between eBGP peers.
A. eBGP peers are usually directly connected to each other.
B. eBGP peers are always directly connected to each other.
C. eBGP peers are never directly connected to each other.
D. eBGP peers are usually directly connected to each other, unless they are in the same autonomous system.
E. eBGP peers are usually not directly connected to each other, additional configuration is required if they are.
Answer: A
更多最新考试信息可登陆www.pass4side.cn网站查看！本文考试题库摘自pass4side.cn 更新时间：2008-9-10
Pass4side Oracle 1Z0-226 独家题库 4
题库内容摘自www.pass4side.cn 。更新时间：2008-9-22
16. Select two correct statements regarding the workflow holds/activities/Exception Management.(Choose two.)
A. The Retry concurrent program can be run only at Execution modE.
B. Retry workflow activities are possible only at individual error levels.
C. Retry workflow activities are possible in batch mode via concurrent program.
D. Retry workflow activities cannot be launched from the Process Messages window.
E. When a ship line activity errors out after the line has progressed and the delivery detail is closed, theline status displays as Notify instead of Retry.
Answer: CE
17. During the requirements-gathering stage, your client states that it wants items purchased from asupplier to be inspecteD. The client wants to know at what point the inventory is available to reservE.When can reservations occur?
A. upon PO Line receipt
B. when the PO is approved
C. after the Inspection step is performed
D. after the Receipt Line Deliver transaction
E. reservations are not possible on inspection items
Answer: D
18. Your client requires Org A to supply Org B with inventory on a need basis. The Internal Order flag ischeckeD. An internal requisition has been created and approveD.What type of receipt would Org B have to perform to receive the goods?
A. RMA receipt
B. Inter-Org Transfer
C. Account Alias receipt
D. Purchase Order receipt
E. Receipt by Shipment Number
Answer: E
19. Your client has an item that is used globally. The site in Colorado is evaluating a local source for theitem. The buyer requires the incoming goods from the local source to be separated from the goodsreceived from nonlocal sources.Which three actions should be performed to meet this requirement? (Choose threE. )
A. Enter the item in the subinventory form.
B. Modify master item attributes to default a subinventory.
C. Change the PO Line receipt routing to Inspection RequireD.
D. Modify organization item attributes to default a subinventory.
E. Create a separate subinventory to stock goods from the local sourcE.
F. Create item transaction default for the item in the Item Master Organization.
G. Insert a separate subinventory on the purchase order and attach Receiver Notes.
H. Ensure that you do not create an item transaction default for the item in the Inventory Organization.
Answer: EGH
20. Which data is provided by Oracle Purchasing to Oracle Inventory?
A. ATP supply, planning supply, and requisition information
B. items, requisition, and interorganization shipment information
C. receipts/deliveries and interorganization shipment information
D. receipts/deliveries, ATP supply, and planning supply information
E. receipts/deliveries, units of measure, ATP supply, and planning supply information
Answer: D
16. Select two correct statements regarding the workflow holds/activities/Exception Management.(Choose two.)
A. The Retry concurrent program can be run only at Execution modE.
B. Retry workflow activities are possible only at individual error levels.
C. Retry workflow activities are possible in batch mode via concurrent program.
D. Retry workflow activities cannot be launched from the Process Messages window.
E. When a ship line activity errors out after the line has progressed and the delivery detail is closed, theline status displays as Notify instead of Retry.
Answer: CE
17. During the requirements-gathering stage, your client states that it wants items purchased from asupplier to be inspecteD. The client wants to know at what point the inventory is available to reservE.When can reservations occur?
A. upon PO Line receipt
B. when the PO is approved
C. after the Inspection step is performed
D. after the Receipt Line Deliver transaction
E. reservations are not possible on inspection items
Answer: D
18. Your client requires Org A to supply Org B with inventory on a need basis. The Internal Order flag ischeckeD. An internal requisition has been created and approveD.What type of receipt would Org B have to perform to receive the goods?
A. RMA receipt
B. Inter-Org Transfer
C. Account Alias receipt
D. Purchase Order receipt
E. Receipt by Shipment Number
Answer: E
19. Your client has an item that is used globally. The site in Colorado is evaluating a local source for theitem. The buyer requires the incoming goods from the local source to be separated from the goodsreceived from nonlocal sources.Which three actions should be performed to meet this requirement? (Choose threE. )
A. Enter the item in the subinventory form.
B. Modify master item attributes to default a subinventory.
C. Change the PO Line receipt routing to Inspection RequireD.
D. Modify organization item attributes to default a subinventory.
E. Create a separate subinventory to stock goods from the local sourcE.
F. Create item transaction default for the item in the Item Master Organization.
G. Insert a separate subinventory on the purchase order and attach Receiver Notes.
H. Ensure that you do not create an item transaction default for the item in the Inventory Organization.
Answer: EGH
20. Which data is provided by Oracle Purchasing to Oracle Inventory?
A. ATP supply, planning supply, and requisition information
B. items, requisition, and interorganization shipment information
C. receipts/deliveries and interorganization shipment information
D. receipts/deliveries, ATP supply, and planning supply information
E. receipts/deliveries, units of measure, ATP supply, and planning supply information
Answer: D
Pass4side Oracle 1Z0-226 独家题库 3
题库内容摘自www.pass4side.cn 。更新时间：2008-9-22
11. PTO Kits consist of _____.
A. a standard BOM
B. a configurable BOM
C. a standard BOM with mandatory included options
D. a configurable BOM with mandatory included optionsE. an engineering BOM with mandatory included options
Answer: C
12. Identify the four statements related to the MOAC functionality. (Choose four.)
A. When querying any transaction, one must specify the operating unit.
B. The Operating Unit field is a display-only field for all the transaction forms.
C. While entering a transaction, the Operating Unit needs to be selected in case the user wants anOperating Unit other than the default.
D. While querying for a transaction, entering the Operating Unit helps the application to query lessernumber of transactions and results in better performancE.
E. A new Operating Unit field has been added to all the forms that allow the user to view and manageSales Orders and Returns across multiple operating units.
F. A new Operating Unit field has been added to all the forms that allow the user to view and manageSales Agreements and Quotes across multiple operating units.
Answer: CDEF
13. Weight and physical dimensions are examples of ____.
A. an item attribute
B. an item parameter
C. an item profile option
D. an item master characteristic
Answer: A
14. Identify three correct statements regarding customer acceptance setups. (Choose threE. )
A. Customer acceptance can be enabled at the inventory organization level.
B. For enabling customer acceptance, no setup is required in OM.
C. Customer acceptance can be enabled at the OM operating-unit level.
D. Define assignment rules for deferral reasons at the customer, site, or item level.
E. The first step to enable customer acceptance is to set the OM system parameter: Enable FulfillmentAcceptancE.F. The second step of the customer acceptance setup is to define customer acceptance deferral reasonsin the AR revenue management setup.
Answer: CEF
15. What are the three necessary setup steps to enable system credit checking on an order? (ChoosethreE. )
A. Assign a credit rule to the order type being useD.
B. Select a warehouse that has credit checking enableD.
C. Enable the Credit Card Security Code system parameter.
D. Use a payment term for which the Credit check box is enableD.
E. Define the customer profile so that the Credit check box is selecteD.
F. Make sure that there is at least one defaulting rule enabled for credit checkinG.
Answer: ADE
11. PTO Kits consist of _____.
A. a standard BOM
B. a configurable BOM
C. a standard BOM with mandatory included options
D. a configurable BOM with mandatory included optionsE. an engineering BOM with mandatory included options
Answer: C
12. Identify the four statements related to the MOAC functionality. (Choose four.)
A. When querying any transaction, one must specify the operating unit.
B. The Operating Unit field is a display-only field for all the transaction forms.
C. While entering a transaction, the Operating Unit needs to be selected in case the user wants anOperating Unit other than the default.
D. While querying for a transaction, entering the Operating Unit helps the application to query lessernumber of transactions and results in better performancE.
E. A new Operating Unit field has been added to all the forms that allow the user to view and manageSales Orders and Returns across multiple operating units.
F. A new Operating Unit field has been added to all the forms that allow the user to view and manageSales Agreements and Quotes across multiple operating units.
Answer: CDEF
13. Weight and physical dimensions are examples of ____.
A. an item attribute
B. an item parameter
C. an item profile option
D. an item master characteristic
Answer: A
14. Identify three correct statements regarding customer acceptance setups. (Choose threE. )
A. Customer acceptance can be enabled at the inventory organization level.
B. For enabling customer acceptance, no setup is required in OM.
C. Customer acceptance can be enabled at the OM operating-unit level.
D. Define assignment rules for deferral reasons at the customer, site, or item level.
E. The first step to enable customer acceptance is to set the OM system parameter: Enable FulfillmentAcceptancE.F. The second step of the customer acceptance setup is to define customer acceptance deferral reasonsin the AR revenue management setup.
Answer: CEF
15. What are the three necessary setup steps to enable system credit checking on an order? (ChoosethreE. )
A. Assign a credit rule to the order type being useD.
B. Select a warehouse that has credit checking enableD.
C. Enable the Credit Card Security Code system parameter.
D. Use a payment term for which the Credit check box is enableD.
E. Define the customer profile so that the Credit check box is selecteD.
F. Make sure that there is at least one defaulting rule enabled for credit checkinG.
Answer: ADE
Pass4side Oracle 1Z0-226 独家题库 2
题库内容摘自www.pass4side.cn 。更新时间：2008-9-22
6. XYZ is a chemical manufacturing company. On a daily basis, it produces 100 kilos of Item A from asingle production batcH.100 kilos of item A manufactured from a single batch has a single expiration datE. However, the purityof item A varies as follows:Category 1: 95%Category 2: 85%Category 3: 50%From an implementation perspective, which setup or process would meet this requirement?
A. Enable lot control. Map three categories as coproducts.
B. Enable lot control for item A. Create three lots to represent the categories.
C. Enable lot control for item A. Create three child lots and link them with the parent lot.
D. Enable lot and grade control for item A. Have three categories mapped with grades.
E. Enable lot and serial control for item A. Create one lot and three categories that are mapped withserial numbers.Answer: D
7. For which type of move order is approval required?
A. Planning Move OrderB. Shipping Move OrderC. Production Move OrderD. Requisition Move OrderE. Replenishment Move OrderAnswer: D8. Identify four functions that a user can perform using the Material WorkbencH. (Choose four)
A. Create move orders.
B. Create and save queries.
C. Change material statuses.
D. Perform miscellaneous issues.
E. Perform miscellaneous receipts.
F. Perform pick confirm transactions.
G. Perform ship confirm transactions.
H. View material in receiving, on-hand quantities, and intransit material.
Answer: ABCH
9. The client has decided that Quality and Discrete Manufacturing will be implemented at a future stage,so new supply from current manufacturing will be added to current inventory on hand by the OpenTransactions InterfacE.The immediate requirement is to go-live with Inventory and Order Management.Which three seeded transaction types can be omitted for material status control? (Choose threE. )
A. average cost update
B. all internal transactions
C. backflush subinventory transfer
D. miscellaneous issues and receipts
E. all transaction types related to Work in Process
F. all transaction types related to Project Manufacturing
Answer: CEF
10. ACME attempts the Pick Release process for delivery lines that have been bookeD.Which three options are valid? (Choose three. )
A. Run the Auto Allocate process.
B. Run the Pick Slip Grouping process.
C. Run the Interface Trip Stop process.
D. Use the Standard Report Submission process (SRS).
E. Execute Online from the Release Sales Order window.
F. Run a concurrent program from the Release Sales Order window.
Answer: DEF
6. XYZ is a chemical manufacturing company. On a daily basis, it produces 100 kilos of Item A from asingle production batcH.100 kilos of item A manufactured from a single batch has a single expiration datE. However, the purityof item A varies as follows:Category 1: 95%Category 2: 85%Category 3: 50%From an implementation perspective, which setup or process would meet this requirement?
A. Enable lot control. Map three categories as coproducts.
B. Enable lot control for item A. Create three lots to represent the categories.
C. Enable lot control for item A. Create three child lots and link them with the parent lot.
D. Enable lot and grade control for item A. Have three categories mapped with grades.
E. Enable lot and serial control for item A. Create one lot and three categories that are mapped withserial numbers.Answer: D
7. For which type of move order is approval required?
A. Planning Move OrderB. Shipping Move OrderC. Production Move OrderD. Requisition Move OrderE. Replenishment Move OrderAnswer: D8. Identify four functions that a user can perform using the Material WorkbencH. (Choose four)
A. Create move orders.
B. Create and save queries.
C. Change material statuses.
D. Perform miscellaneous issues.
E. Perform miscellaneous receipts.
F. Perform pick confirm transactions.
G. Perform ship confirm transactions.
H. View material in receiving, on-hand quantities, and intransit material.
Answer: ABCH
9. The client has decided that Quality and Discrete Manufacturing will be implemented at a future stage,so new supply from current manufacturing will be added to current inventory on hand by the OpenTransactions InterfacE.The immediate requirement is to go-live with Inventory and Order Management.Which three seeded transaction types can be omitted for material status control? (Choose threE. )
A. average cost update
B. all internal transactions
C. backflush subinventory transfer
D. miscellaneous issues and receipts
E. all transaction types related to Work in Process
F. all transaction types related to Project Manufacturing
Answer: CEF
10. ACME attempts the Pick Release process for delivery lines that have been bookeD.Which three options are valid? (Choose three. )
A. Run the Auto Allocate process.
B. Run the Pick Slip Grouping process.
C. Run the Interface Trip Stop process.
D. Use the Standard Report Submission process (SRS).
E. Execute Online from the Release Sales Order window.
F. Run a concurrent program from the Release Sales Order window.
Answer: DEF
Pass4side Oracle 1Z0-226 独家题库 1
题库内容摘自http://www.pass4side.cn/ 。更新时间：2008-9-22
1. The Check ATP option is enabled for an item in the Finished Goods subinventory.Which action will occur?
A. Check the quantity requested against forecast.
B. Generate a requisition for the requested quantity.
C. Permit order booking based on a successful test.
D. Check the quantity requested against safety stock.
E. Check the quantity requested against Economic Order Quantity (EOQ).
Answer: C
2. The client requires that cycle counts are entered by the warehouse stafF. However, only thewarehouse manager can schedule counts, generate count requests, and approve the counts that are outof tolerancE.What should you consider when setting up the cycle counting process? (Choose three. )
A. the frequency of the recounts required
B. the number of automatic recounts required
C. the tolerance level for automatic adjustment
D. Modify the workday calendar used by the warehousE.
E. the responsibility that has access to the Approve Counts function
F. the number of serial and/or lot controlled items included in the count
Answer: BCE
3. Company Z has two sites. Both sites are inventory organizations. One is in Colorado, the other is inNew Jersey. Inventory is expected to travel between the two, in both directions.The following requirements are identical for the two organizations:a) Ownership transfer occurs upon ship confirm.b) There is a two-step receiving process.c) Only approved orders would be performeD.Which setups in Shipping Networks meet these criteria?
A. Transit Type = Direct, FOB = Receipt, Receipt Routing = Direct, Internal Order Required = checked
B. Transit Type = Intransit, FOB = Receipt, Receipt Routing = Direct, Internal Order Required =unchecked
C. Transit Type = Intransit, FOB = Receipt, Receipt Routing = Standard, Internal Order Required =checked
D. Transit Type = Direct, FOB = Shipment, Receipt Routing = Standard, Internal Order Required =checkedE. Transit Type = Intransit, FOB = Shipment, Receipt Routing = Inspection, Internal Order Required =checked
Answer: C
4. Each UOM class must have a base unit specifie D.Which represents a base unit for the UOM Class Quantity?A. OneB. EachC. CaseD. GrossE. DozenAnswer: B
5. A user informs you about the inability to create a requisition using category 110.33. The Purchasingcategory structure is set up as Item Category.Commodity.The user has described the problem as follows:"I am able to select 110 for the item category and 33 for the commodity, but when I click OK I receive anerror."Identify two reasons for the error. (Choose two.)A. The commodity 33 has been deactivateD.B. The item category 110 has been deactivateD.C. The category 110.33 is not assigned to a buyer.D. Category 110.33 is not set up in the categories form.E. 110.33 is not assigned to the Purchasing category set.F. 110.33 has not been added to the appropriate value set.G. Allow Dynamic Inserts is not checked for the Purchasing category flexfielD.Answer: DE
1. The Check ATP option is enabled for an item in the Finished Goods subinventory.Which action will occur?
A. Check the quantity requested against forecast.
B. Generate a requisition for the requested quantity.
C. Permit order booking based on a successful test.
D. Check the quantity requested against safety stock.
E. Check the quantity requested against Economic Order Quantity (EOQ).
Answer: C
2. The client requires that cycle counts are entered by the warehouse stafF. However, only thewarehouse manager can schedule counts, generate count requests, and approve the counts that are outof tolerancE.What should you consider when setting up the cycle counting process? (Choose three. )
A. the frequency of the recounts required
B. the number of automatic recounts required
C. the tolerance level for automatic adjustment
D. Modify the workday calendar used by the warehousE.
E. the responsibility that has access to the Approve Counts function
F. the number of serial and/or lot controlled items included in the count
Answer: BCE
3. Company Z has two sites. Both sites are inventory organizations. One is in Colorado, the other is inNew Jersey. Inventory is expected to travel between the two, in both directions.The following requirements are identical for the two organizations:a) Ownership transfer occurs upon ship confirm.b) There is a two-step receiving process.c) Only approved orders would be performeD.Which setups in Shipping Networks meet these criteria?
A. Transit Type = Direct, FOB = Receipt, Receipt Routing = Direct, Internal Order Required = checked
B. Transit Type = Intransit, FOB = Receipt, Receipt Routing = Direct, Internal Order Required =unchecked
C. Transit Type = Intransit, FOB = Receipt, Receipt Routing = Standard, Internal Order Required =checked
D. Transit Type = Direct, FOB = Shipment, Receipt Routing = Standard, Internal Order Required =checkedE. Transit Type = Intransit, FOB = Shipment, Receipt Routing = Inspection, Internal Order Required =checked
Answer: C
4. Each UOM class must have a base unit specifie D.Which represents a base unit for the UOM Class Quantity?A. OneB. EachC. CaseD. GrossE. DozenAnswer: B
5. A user informs you about the inability to create a requisition using category 110.33. The Purchasingcategory structure is set up as Item Category.Commodity.The user has described the problem as follows:"I am able to select 110 for the item category and 33 for the commodity, but when I click OK I receive anerror."Identify two reasons for the error. (Choose two.)A. The commodity 33 has been deactivateD.B. The item category 110 has been deactivateD.C. The category 110.33 is not assigned to a buyer.D. Category 110.33 is not set up in the categories form.E. 110.33 is not assigned to the Purchasing category set.F. 110.33 has not been added to the appropriate value set.G. Allow Dynamic Inserts is not checked for the Purchasing category flexfielD.Answer: DE
2008年9月23日星期二
Pass4side Oracle 1Z0-238 独家认证题库 4
题库内容摘自www.pass4side.cn 。更新时间：2008-9-22
16. Before you apply a patch, you read the readme.txt file.One of the areas of Oracle Applications to which the patch will be applied is JAVA_TOP.The readme file mentions that you may need to generate product JAR files in the AD Administration utilities afterthe patch is applied.When generating product JAR files, the AD Administration utility will prompt you with the question: Do youwant to force the generation of all JAR files?What are the three occasions when you need to force the generation of all JAR files? (Choose three.)
A.after changing your digital signature
B.after updating to a new Java version
C.if you find you have missing or out-of-date JAR files
D.if you are upgrading the Oracle Developer technology stack
Answer: ABD
17. You run the AD Administration utility and select the Relink Applications programs.You answered the following questions during the utility run:Do you wish to proceed with the relink [Yes]? (You answer Yes.)Enter the list of products to link ("all" for all products) [all]? (You answer "ad." )Do you want to generate specific executables for each selected product [No]? (You answer Yes.)AD Administration can relink your Oracle Applications programs with debuginformation. Oracle recommends that you do not relink your programswith debug information unless asked to do so by Oracle Support Services.Do you want to relink with debug information [No]? (You answer No.)What is the next question asked by adadmin?
A.It gives you a list of all executables to choose from.
B.It gives you the list of "ad" executables to choose from.
C.It gives you the list of all executables except "ad" to choose from.
D.It asks no question. It displays the message "Review the messages above, then press [Return] to continue."
Answer: D
18. You discover that you will be applying an application patch on your APPL_TOP by using AutoPatch, whichcontains a compatible feature, the prereq line.To ensure that the automatic, prerequisite patch-checking feature operates during the application of the patch, youmust run AD Administration, Maintain Snapshot Information, then perform some key tasks, and then AutoPatch.Select four key Maintain Snapshot Information tasks or combination of tasks that will ensure that the prerequisitepatch-checking feature operates during the application of the patch. (Choose four.)
A.Update a current view snapshot, or create a named snapshot.
B.Export a snapshot to a file, and then delete the named snapshot.
C.Import an up-to-date snapshot from a file from a different APPL_TOP.
D.List snapshots, delete the named snapshot, and create a named snapshot.
E.Copy the existing snapshot, delete the named snapshot, and then create a named snapshot.
Answer: ACDE
19. AD Administration contains a utility named Maintain Snapshot Information. Which statements correctlydescribe the functionality of this utility? (Choose all that apply.)
A.You can create a copy of an existing snapshot.
B.You can delete the current view snapshot.
C.You can create a list of the current view and named snapshots stored in your system.
D.You can export an existing snapshot to a file for storage or to another system.
E.You can update the current view snapshot with any changes to the snapshot since the last update.
Answer: ACDE
20. Identify two ways in which you validate the APPS schema in the Oracle Applications R12 E-Business Suitesetup. (Choose two.)
A.Run the /appsutil/scripts//advrfapp.sh script.
B.Run the AD Administration utility in noninteractive mode with the default file havingmenu_option=VALIDATE_APPS.
C.Run the AD Administration utility in interactive mode, and then select Compile/Reload Applications DatabaseEntities menu > Compile APPS Schema option.
D. Use SQL*PLUS / @$AD_TOP/admin/sql/advrfapp.sql .
Answer: BD
16. Before you apply a patch, you read the readme.txt file.One of the areas of Oracle Applications to which the patch will be applied is JAVA_TOP.The readme file mentions that you may need to generate product JAR files in the AD Administration utilities afterthe patch is applied.When generating product JAR files, the AD Administration utility will prompt you with the question: Do youwant to force the generation of all JAR files?What are the three occasions when you need to force the generation of all JAR files? (Choose three.)
A.after changing your digital signature
B.after updating to a new Java version
C.if you find you have missing or out-of-date JAR files
D.if you are upgrading the Oracle Developer technology stack
Answer: ABD
17. You run the AD Administration utility and select the Relink Applications programs.You answered the following questions during the utility run:Do you wish to proceed with the relink [Yes]? (You answer Yes.)Enter the list of products to link ("all" for all products) [all]? (You answer "ad." )Do you want to generate specific executables for each selected product [No]? (You answer Yes.)AD Administration can relink your Oracle Applications programs with debuginformation. Oracle recommends that you do not relink your programswith debug information unless asked to do so by Oracle Support Services.Do you want to relink with debug information [No]? (You answer No.)What is the next question asked by adadmin?
A.It gives you a list of all executables to choose from.
B.It gives you the list of "ad" executables to choose from.
C.It gives you the list of all executables except "ad" to choose from.
D.It asks no question. It displays the message "Review the messages above, then press [Return] to continue."
Answer: D
18. You discover that you will be applying an application patch on your APPL_TOP by using AutoPatch, whichcontains a compatible feature, the prereq line.To ensure that the automatic, prerequisite patch-checking feature operates during the application of the patch, youmust run AD Administration, Maintain Snapshot Information, then perform some key tasks, and then AutoPatch.Select four key Maintain Snapshot Information tasks or combination of tasks that will ensure that the prerequisitepatch-checking feature operates during the application of the patch. (Choose four.)
A.Update a current view snapshot, or create a named snapshot.
B.Export a snapshot to a file, and then delete the named snapshot.
C.Import an up-to-date snapshot from a file from a different APPL_TOP.
D.List snapshots, delete the named snapshot, and create a named snapshot.
E.Copy the existing snapshot, delete the named snapshot, and then create a named snapshot.
Answer: ACDE
19. AD Administration contains a utility named Maintain Snapshot Information. Which statements correctlydescribe the functionality of this utility? (Choose all that apply.)
A.You can create a copy of an existing snapshot.
B.You can delete the current view snapshot.
C.You can create a list of the current view and named snapshots stored in your system.
D.You can export an existing snapshot to a file for storage or to another system.
E.You can update the current view snapshot with any changes to the snapshot since the last update.
Answer: ACDE
20. Identify two ways in which you validate the APPS schema in the Oracle Applications R12 E-Business Suitesetup. (Choose two.)
A.Run the /appsutil/scripts//advrfapp.sh script.
B.Run the AD Administration utility in noninteractive mode with the default file havingmenu_option=VALIDATE_APPS.
C.Run the AD Administration utility in interactive mode, and then select Compile/Reload Applications DatabaseEntities menu > Compile APPS Schema option.
D. Use SQL*PLUS / @$AD_TOP/admin/sql/advrfapp.sql .
Answer: BD
Pass4side Oracle 1Z0-238 独家认证题库 3
题库内容摘自www.pass4side.cn 。更新时间：2008-9-22
12. During installation, the Rapid Install process creates ______ that are used to start and stop the server processeson the database tier.
A.JServer load balancers
B.cost-based optimizers
C.database resource managers
D.session-persistent load balancers
E.database-tier server process scripts
Answer: E
13. Which command can be used only with a single-node installation?
A.rapidwiz -restart
B.rapidwiz -techstack
C.rapidwiz -servername
D.rapidwiz -silent -config
Answer: C
14. You experience report-error problems in the Inventory module after applying a patch to the same module.You run the AD Administration utility, and select the Generate Application Files menu. Because you have reportproblems, you decide to run Generate Report Files.You answered the following questions during the utility run:1. Do you want to generate Oracle report objects using the current character set? (You answer Yes.)2. Do you want to regenerate the Oracle reports PL/SQL library files? (You answer No.)3. Do you want to regenerate Oracle reports executable files? (You answer Yes.)4. For which products do you want to generate Oracle report objects? (You answer "all reports in INV.")After you run the AD utilities, most reports in Inventory run with no errors. However, you still experience errorswith two reports.Which two statements explain why the two reports still run with errors? (Choose two.)A.You have reports in a different language.
B.You have reports with external library files.
C.You have custom reports in a custom directory.
D.You have reports from a different module being referenced on the Inventory report menu.
Answer: B
15. You just brought the middle tier back after a hardware problem has been fixed. Oracle Applicationsnow experience problems with an entire product group of forms (fnd), which includes the sign-on form.You decide that you will generate the forms files in AD Administration to see whether this will fix theproblem.You answered the prompts from the utility as follows:1. Do you want to generate Oracle Forms using your current character set? (Yes)2. Do you want to regenerate Oracle Forms PL/SQL library files? (Yes)3. Do you want to regenerate Oracle Forms executable files? (Yes)4. Do you want to regenerate Oracle Forms menu files? (Yes)5. Enter the list of products, or enter 'all' [all]: (fnd)6. Do you want to generate specific form objects for each selected product? (Yes)7. Enter libraries and menus to generate, or enter 'all' [all]: (APPCORE.pll, the main library)8. Enter forms to generate, or enter 'all' [all]: FNDSCSGN.fmxThe utility finished with no errors in the log file.What is the outcome of running the adadmin utility?
A.All forms in the product group fnd now render with errors.
B.All forms in the product group fnd now render without errors.
C.All forms but one in the product group fnd now render with errors.
D.All forms but one in the product group fnd now render without errors.
Answer: C
12. During installation, the Rapid Install process creates ______ that are used to start and stop the server processeson the database tier.
A.JServer load balancers
B.cost-based optimizers
C.database resource managers
D.session-persistent load balancers
E.database-tier server process scripts
Answer: E
13. Which command can be used only with a single-node installation?
A.rapidwiz -restart
B.rapidwiz -techstack
C.rapidwiz -servername
D.rapidwiz -silent -config
Answer: C
14. You experience report-error problems in the Inventory module after applying a patch to the same module.You run the AD Administration utility, and select the Generate Application Files menu. Because you have reportproblems, you decide to run Generate Report Files.You answered the following questions during the utility run:1. Do you want to generate Oracle report objects using the current character set? (You answer Yes.)2. Do you want to regenerate the Oracle reports PL/SQL library files? (You answer No.)3. Do you want to regenerate Oracle reports executable files? (You answer Yes.)4. For which products do you want to generate Oracle report objects? (You answer "all reports in INV.")After you run the AD utilities, most reports in Inventory run with no errors. However, you still experience errorswith two reports.Which two statements explain why the two reports still run with errors? (Choose two.)A.You have reports in a different language.
B.You have reports with external library files.
C.You have custom reports in a custom directory.
D.You have reports from a different module being referenced on the Inventory report menu.
Answer: B
15. You just brought the middle tier back after a hardware problem has been fixed. Oracle Applicationsnow experience problems with an entire product group of forms (fnd), which includes the sign-on form.You decide that you will generate the forms files in AD Administration to see whether this will fix theproblem.You answered the prompts from the utility as follows:1. Do you want to generate Oracle Forms using your current character set? (Yes)2. Do you want to regenerate Oracle Forms PL/SQL library files? (Yes)3. Do you want to regenerate Oracle Forms executable files? (Yes)4. Do you want to regenerate Oracle Forms menu files? (Yes)5. Enter the list of products, or enter 'all' [all]: (fnd)6. Do you want to generate specific form objects for each selected product? (Yes)7. Enter libraries and menus to generate, or enter 'all' [all]: (APPCORE.pll, the main library)8. Enter forms to generate, or enter 'all' [all]: FNDSCSGN.fmxThe utility finished with no errors in the log file.What is the outcome of running the adadmin utility?
A.All forms in the product group fnd now render with errors.
B.All forms in the product group fnd now render without errors.
C.All forms but one in the product group fnd now render with errors.
D.All forms but one in the product group fnd now render without errors.
Answer: C
Pass4side Oracle 1Z0-238 独家认证题库 2
题库内容摘自www.pass4side.cn 。更新时间：2008-9-22
6. Which table is used by AutoPatch as a staging area for the job information in parallel mode and needs to bedropped to start a new autopatch session if the earlier session failed?A.FND_JOBS
B.FND_PROCESSES
C.FND_INSTALL_PROCESSES
D.FND_INSTALLED_PROCESSES
Answer: C
7. If the patch is running in Pre-Install mode, where would the patch history files be stored in Oracle ApplicationsR12 configured on a UNIX operating system?A.$AD_TOP/admin
B.$APPL_TOP/admin
C.$TEMP/runInstaller
D.$APPL_TOP/admin/
E.$COMMON_TOP/admin/
Answer: D
8. As part of the cloning process, the Applications DBA needs to copy the application tier file system to the targetsystem.Which step is NOT a part of this process?
A.Shut down the application tier server processes.
B.Log on to the target system application tier nodes as the oracle user.
C.Copy the APPL_TOP directory from the source node to the target node.
D.Copy the directory from the source node to the target node.
E.Copy the directory from the source node to the target node.
F.Copy the directory from the source node to the target node.
G.Copy the <806> directory from the source node to the target node.
Answer: B
9. While working with Web forms an application user sometimes comes across a performance issue. The initialscreen takes too long to appear with the Web form screen, showing the status "Downloading JAR files..." for along time.Identify the reasons for this. (Choose two.)
A.It always takes time to load the Web forms.
B.An older version of Sun J2SE plug-in is installed on the Desktop tier.
C.JAR files for the Forms client applet are downloaded automatically the first time it is used.
D.The browser will automatically retrieve new JAR files if they have changed on the application tier.
E.The Internet Explorer browser security level should be set as "Low" for the zone that contains the OracleApplication Release 12 Web pages.
Answer: CD
10. After the successful installation of Oracle Applications Release 12, environment files are created.Which environment file is used to identify and describe third-party and custom applications linked with OracleApplications?
A.the context file
B.the devenv.env file
C.the fndenv.env file
D.the adovars.env file
E.the adconfig.txt file
Answer: B
6. Which table is used by AutoPatch as a staging area for the job information in parallel mode and needs to bedropped to start a new autopatch session if the earlier session failed?A.FND_JOBS
B.FND_PROCESSES
C.FND_INSTALL_PROCESSES
D.FND_INSTALLED_PROCESSES
Answer: C
7. If the patch is running in Pre-Install mode, where would the patch history files be stored in Oracle ApplicationsR12 configured on a UNIX operating system?A.$AD_TOP/admin
B.$APPL_TOP/admin
C.$TEMP/runInstaller
D.$APPL_TOP/admin/
E.$COMMON_TOP/admin/
Answer: D
8. As part of the cloning process, the Applications DBA needs to copy the application tier file system to the targetsystem.Which step is NOT a part of this process?
A.Shut down the application tier server processes.
B.Log on to the target system application tier nodes as the oracle user.
C.Copy the APPL_TOP directory from the source node to the target node.
D.Copy the directory from the source node to the target node.
E.Copy the directory from the source node to the target node.
F.Copy the directory from the source node to the target node.
G.Copy the <806> directory from the source node to the target node.
Answer: B
9. While working with Web forms an application user sometimes comes across a performance issue. The initialscreen takes too long to appear with the Web form screen, showing the status "Downloading JAR files..." for along time.Identify the reasons for this. (Choose two.)
A.It always takes time to load the Web forms.
B.An older version of Sun J2SE plug-in is installed on the Desktop tier.
C.JAR files for the Forms client applet are downloaded automatically the first time it is used.
D.The browser will automatically retrieve new JAR files if they have changed on the application tier.
E.The Internet Explorer browser security level should be set as "Low" for the zone that contains the OracleApplication Release 12 Web pages.
Answer: CD
10. After the successful installation of Oracle Applications Release 12, environment files are created.Which environment file is used to identify and describe third-party and custom applications linked with OracleApplications?
A.the context file
B.the devenv.env file
C.the fndenv.env file
D.the adovars.env file
E.the adconfig.txt file
Answer: B
Pass4side Oracle 1Z0-238 独家认证题库 1
题库内容摘自www.pass4side.cn 。更新时间：2008-9-22
1. What are the two occasions when it is appropriate to run "Compile APPS schema" by using the ADAdministration utility in the Oracle Applications R12 E-Business Suite environment? (Choose two.)
A.during the Oracle Applications R12 E-Business Suite upgrade process
B.when custom packages are moved to the APPS schema and need to be compiled
C.after enabling the multiple reporting currencies in the Oracle Applications R12 E-Business Suite environment
D.after enabling the multiorganization functionality in the Oracle Applications R12 E-Business Suite environment
E.when encountering invalid objects in the SYS and SYSTEM schemas in the Oracle Applications R12E-Business Suite database
Answer: AB
2. What are the two possible sequences of worker status while a job is being completed by a worker? (Choosetwo.)
A.Waiting => Assigned => Running => Completed
B.Assigned => Waiting => Running => Completed
C.Waiting => Assigned => Running => Failed => Fixed, Restart => Restarted => Completed
D.Assigned => Waiting => Running => Failed => Fixed, Restart => Restarted => CompletedE.Waiting => Assigned => Running => Failed => Fixed, Restart => Restarted => Running => Completed
Answer: AC
3. Identify the files that are changed when you run AutoConfig. (Choose all that apply.)A./listener.ora
B./.env
C./admin/adconfig.txt
D./.env
E./appl/admin/.xml
Answer: ABD
4. Identify the patch that you apply to upgrade the Oracle Applications system from the 11.5.5 version to the11.5.10 version.
A.diagnostic patch
B.stand-alone patch
C.maintenance pack
D.product family release update pack
Answer: C
5. You want to apply a patch on your Oracle Applications system. Before doing this, you want to view the filesthat are new, changed, and ignored while applying the patch.Which feature of the Patch Wizard would help you accomplish this?
A.Patch Filters
B.Patch Impact Analysis
C.Recommended Patches
D.Patch Information Bundle
Answer: B
1. What are the two occasions when it is appropriate to run "Compile APPS schema" by using the ADAdministration utility in the Oracle Applications R12 E-Business Suite environment? (Choose two.)
A.during the Oracle Applications R12 E-Business Suite upgrade process
B.when custom packages are moved to the APPS schema and need to be compiled
C.after enabling the multiple reporting currencies in the Oracle Applications R12 E-Business Suite environment
D.after enabling the multiorganization functionality in the Oracle Applications R12 E-Business Suite environment
E.when encountering invalid objects in the SYS and SYSTEM schemas in the Oracle Applications R12E-Business Suite database
Answer: AB
2. What are the two possible sequences of worker status while a job is being completed by a worker? (Choosetwo.)
A.Waiting => Assigned => Running => Completed
B.Assigned => Waiting => Running => Completed
C.Waiting => Assigned => Running => Failed => Fixed, Restart => Restarted => Completed
D.Assigned => Waiting => Running => Failed => Fixed, Restart => Restarted => CompletedE.Waiting => Assigned => Running => Failed => Fixed, Restart => Restarted => Running => Completed
Answer: AC
3. Identify the files that are changed when you run AutoConfig. (Choose all that apply.)A./listener.ora
B./.env
C./admin/adconfig.txt
D./.env
E./appl/admin/.xml
Answer: ABD
4. Identify the patch that you apply to upgrade the Oracle Applications system from the 11.5.5 version to the11.5.10 version.
A.diagnostic patch
B.stand-alone patch
C.maintenance pack
D.product family release update pack
Answer: C
5. You want to apply a patch on your Oracle Applications system. Before doing this, you want to view the filesthat are new, changed, and ignored while applying the patch.Which feature of the Patch Wizard would help you accomplish this?
A.Patch Filters
B.Patch Impact Analysis
C.Recommended Patches
D.Patch Information Bundle
Answer: B
Pass4side IBM 000-742 考试题库 4
题库内容摘自www.pass4side.cn 。更新时间：2008-9-20
16. Refer to the exhibit to answer the question. The customer wants to run centralized backups. Assuming auniform change rate for the data on all of the servers shown, which of the following nodes is the best candidate fora backup server?
A. Node A
B. Node B
C. Node C
D. Node E
Answer: C
17. When choosing between an IBM TotalStorage 3582 Tape Library and an IBM TotalStorage 3583 Tape Libraryfor an open system environment, which requirement differentiates the two libraries?
A. Standalone or rack mounted
B. SCSI or FC attachment
C. Logical library sharing
D. Upgradeable storage slot capacity
Answer: D
18. A customer has reviewed the Storage Specialist's proposal for a centralized disk solution supporting Sun, HP,Intel, IBM eServer pSeries and iSeries servers. The customer's feedback indicates that the solution exceeds theirbudget. They also indicate that they have signed an agreement outsourcing their iSeries applications. Which ofthe following would be the most appropriate change to the proposal?
A. Reduce the amount of disk configured in the subsystem.
B. Reduce the amount of disk configured in the subsystem and reduce the SAN port count.
C. Reduce the amount of disk configured, change the subsystem to a NAS solution and eliminate the SAN.
D. Reduce the amount of disk configured, change the subsystem to IBM TotalStorage DS4000 and reduce theSAN port count.
Answer: D
19. Which of the following is a competitive advantage of the IBM TotalStorage DS4300 compared to the HPMSA1000?
A. FlashCopy option
B. Remote Mirroring option
C. Additional host configuration options
D. Better reliability, availability, and serviceability (RAS) characteristics
Answer: B
20. A customer has a requirement for recall of tape data. The media choice must have the longest archival life.Which of the following would be the most appropriate selection?
A. LTO
B. DLT
C. SDLT
D. 3590
Answer: A
16. Refer to the exhibit to answer the question. The customer wants to run centralized backups. Assuming auniform change rate for the data on all of the servers shown, which of the following nodes is the best candidate fora backup server?
A. Node A
B. Node B
C. Node C
D. Node E
Answer: C
17. When choosing between an IBM TotalStorage 3582 Tape Library and an IBM TotalStorage 3583 Tape Libraryfor an open system environment, which requirement differentiates the two libraries?
A. Standalone or rack mounted
B. SCSI or FC attachment
C. Logical library sharing
D. Upgradeable storage slot capacity
Answer: D
18. A customer has reviewed the Storage Specialist's proposal for a centralized disk solution supporting Sun, HP,Intel, IBM eServer pSeries and iSeries servers. The customer's feedback indicates that the solution exceeds theirbudget. They also indicate that they have signed an agreement outsourcing their iSeries applications. Which ofthe following would be the most appropriate change to the proposal?
A. Reduce the amount of disk configured in the subsystem.
B. Reduce the amount of disk configured in the subsystem and reduce the SAN port count.
C. Reduce the amount of disk configured, change the subsystem to a NAS solution and eliminate the SAN.
D. Reduce the amount of disk configured, change the subsystem to IBM TotalStorage DS4000 and reduce theSAN port count.
Answer: D
19. Which of the following is a competitive advantage of the IBM TotalStorage DS4300 compared to the HPMSA1000?
A. FlashCopy option
B. Remote Mirroring option
C. Additional host configuration options
D. Better reliability, availability, and serviceability (RAS) characteristics
Answer: B
20. A customer has a requirement for recall of tape data. The media choice must have the longest archival life.Which of the following would be the most appropriate selection?
A. LTO
B. DLT
C. SDLT
D. 3590
Answer: A
Pass4side IBM 000-742 考试题库 3
题库内容摘自www.pass4side.cn 。更新时间：2008-9-20
11. A customer will be using an IBM TotalStorage DS4000 Storage Subsystem. In order to provide the highestdata availability for a database server, which of the following is the most appropriate hardware RAID technologyto recommend?
A. RAID 1
B. RAID 5
C. RAID 10
D. RAID 50
Answer: C
12. A customer is migrating a 600 GB Oracle database from an older IBM eServer pSeries server to a new one.The data is on a 2 TB IBM TotalStorage Enterprise Storage Server (ESS) that is 80% full. What is the easiestway to move the data to the new server?
A. Assign new LUNs to the new system, backup the data with the existing tape library, and restore it on the newsystem.
B. Use IBM TotalStorage ESS Specialist to assign the existing LUNs to the new server and use AIX LVMimportvg to acquire the existing data.
C. Create new LUNs as targets, perform FlashCopy to those LUNs, and assign the target LUNs to the new server.
D. Create new LUNs as targets, perform Metro Mirror to those LUNs, and assign the target LUNs to the newserver.
Answer: B
13. Which of the following is a feature of all IBM TotalStorage Ultrium tape drives?
A. Statistical Analysis and Reporting System (SARS)
B. Native switched fabric 2 Gb Fibre Channel interface
C. WORM Tape
D. 64 MB buffer
Answer: A
14. After a long competitive sales cycle, the customer has decided to implement their first centralized storagesolution on the IBM TotalStorage DS4500 Storage Server. To help ensure a successful installation, which of thefollowing should be proposed as part of the solution?
A. Service Alert
B. Business Continuance Services
C. 3-Year Warranty Service Upgrade
D. Planning and Implementation Services
Answer: D
15. A customer would like to integrate a Windows file server into the centralized IBM Tivoli Storage Manager(TSM) backup solution. The servers are SAN attached to an IBM Total Storage DS4500. There is very little LANbandwidth to spare. What should the Storage Specialist recommend?
A. Implement an IBM TSM LAN Free solution.
B. Add a larger dedicated tape drive and have IBM TSM manage it remotely.
C. Install IBM TSM for Application Servers.
D. Install the IBM TSM client and backup over the network.
Answer: A
11. A customer will be using an IBM TotalStorage DS4000 Storage Subsystem. In order to provide the highestdata availability for a database server, which of the following is the most appropriate hardware RAID technologyto recommend?
A. RAID 1
B. RAID 5
C. RAID 10
D. RAID 50
Answer: C
12. A customer is migrating a 600 GB Oracle database from an older IBM eServer pSeries server to a new one.The data is on a 2 TB IBM TotalStorage Enterprise Storage Server (ESS) that is 80% full. What is the easiestway to move the data to the new server?
A. Assign new LUNs to the new system, backup the data with the existing tape library, and restore it on the newsystem.
B. Use IBM TotalStorage ESS Specialist to assign the existing LUNs to the new server and use AIX LVMimportvg to acquire the existing data.
C. Create new LUNs as targets, perform FlashCopy to those LUNs, and assign the target LUNs to the new server.
D. Create new LUNs as targets, perform Metro Mirror to those LUNs, and assign the target LUNs to the newserver.
Answer: B
13. Which of the following is a feature of all IBM TotalStorage Ultrium tape drives?
A. Statistical Analysis and Reporting System (SARS)
B. Native switched fabric 2 Gb Fibre Channel interface
C. WORM Tape
D. 64 MB buffer
Answer: A
14. After a long competitive sales cycle, the customer has decided to implement their first centralized storagesolution on the IBM TotalStorage DS4500 Storage Server. To help ensure a successful installation, which of thefollowing should be proposed as part of the solution?
A. Service Alert
B. Business Continuance Services
C. 3-Year Warranty Service Upgrade
D. Planning and Implementation Services
Answer: D
15. A customer would like to integrate a Windows file server into the centralized IBM Tivoli Storage Manager(TSM) backup solution. The servers are SAN attached to an IBM Total Storage DS4500. There is very little LANbandwidth to spare. What should the Storage Specialist recommend?
A. Implement an IBM TSM LAN Free solution.
B. Add a larger dedicated tape drive and have IBM TSM manage it remotely.
C. Install IBM TSM for Application Servers.
D. Install the IBM TSM client and backup over the network.
Answer: A
Pass4side IBM 000-742 考试题库 2
题库内容摘自http://www.pass4side.cn/ 。更新时间：2008-9-20
6. A customer owns a 150 GB usable RAID 5 SCSI disk subsystem attached to a single host and wants to increasedata throughput, reliability, availability, and serviceability. Cost is a significant consideration. Which of thefollowing is most likely to satisfy all of these requirements?
A. Convert the RAID 5 subsystem to a RAID 1 subsystem.
B. Convert the existing subsystem to dual-attached SCSI.
C. Replace the existing subsystem with an IBM TotalStorage DS4000 Storage Server.
D. Replace the existing subsystem with an IBM TotalStorage DS8000 Storage Server.
Answer: C
7. A distributor is planning to open five locations, with each location requiring a local nightly backup of 500 GBof data from a Sun server. Performance and cost are key requirements. Which of the following is the bestsolution?
A. IBM TotalStorage 3581 Tape Autoloader
B. IBM TotalStorage 3590 Model H11 Tape Drive
C. IBM TotalStorage 3592 Model J1A Tape Drive
D. IBM TotalStorage 7205 Model 550 External SDLT320 Tape Drive
Answer: A
8. A customer is currently running a mail server application and is interested in a new storage subsystem. Whichof the following will have the most impact in sizing the subsystem?
A. Record size
B. Logical volume partitioning
C. Data security
D. Number of users
Answer: D
9. A large customer environment consists of 16 Intel-based servers that support electronic mail. The servers haveexceeded their disk storage capacity and the customer would like to centralize disk storage. Which of thefollowing solutions should be recommended?
A. IBM TotalStorage NAS Gateway 500
B. IBM TotalStorage SAN Volume Controller
C. IBM TotalStorage DS4000 Storage Server
D. IBM Tivoli Storage Manager for Space Management
Answer: C
10. A customer is running a SAP R/3 application using Oracle Parallel Server as the database manager on an IBMeServer pSeries server. The customer would like two servers to share the same Oracle database. Which of thefollowing IBM storage products would NOT be recommended to meet the customer's requirement?
A. IBM TotalStorage EXP Plus
B. IBM TotalStorage SAN Filesystem
C. IBM TotalStorage NAS Gateway 500
D. IBM TotalStorage SAN Volume Controller
Answer: C
6. A customer owns a 150 GB usable RAID 5 SCSI disk subsystem attached to a single host and wants to increasedata throughput, reliability, availability, and serviceability. Cost is a significant consideration. Which of thefollowing is most likely to satisfy all of these requirements?
A. Convert the RAID 5 subsystem to a RAID 1 subsystem.
B. Convert the existing subsystem to dual-attached SCSI.
C. Replace the existing subsystem with an IBM TotalStorage DS4000 Storage Server.
D. Replace the existing subsystem with an IBM TotalStorage DS8000 Storage Server.
Answer: C
7. A distributor is planning to open five locations, with each location requiring a local nightly backup of 500 GBof data from a Sun server. Performance and cost are key requirements. Which of the following is the bestsolution?
A. IBM TotalStorage 3581 Tape Autoloader
B. IBM TotalStorage 3590 Model H11 Tape Drive
C. IBM TotalStorage 3592 Model J1A Tape Drive
D. IBM TotalStorage 7205 Model 550 External SDLT320 Tape Drive
Answer: A
8. A customer is currently running a mail server application and is interested in a new storage subsystem. Whichof the following will have the most impact in sizing the subsystem?
A. Record size
B. Logical volume partitioning
C. Data security
D. Number of users
Answer: D
9. A large customer environment consists of 16 Intel-based servers that support electronic mail. The servers haveexceeded their disk storage capacity and the customer would like to centralize disk storage. Which of thefollowing solutions should be recommended?
A. IBM TotalStorage NAS Gateway 500
B. IBM TotalStorage SAN Volume Controller
C. IBM TotalStorage DS4000 Storage Server
D. IBM Tivoli Storage Manager for Space Management
Answer: C
10. A customer is running a SAP R/3 application using Oracle Parallel Server as the database manager on an IBMeServer pSeries server. The customer would like two servers to share the same Oracle database. Which of thefollowing IBM storage products would NOT be recommended to meet the customer's requirement?
A. IBM TotalStorage EXP Plus
B. IBM TotalStorage SAN Filesystem
C. IBM TotalStorage NAS Gateway 500
D. IBM TotalStorage SAN Volume Controller
Answer: C
Pass4side IBM 000-742 (1)
Pass4side IBM 000-742（更新时间20008-9-20）考试题库 1 题库内容摘自www.pass4side.cn 。更新时间：2008-9-20
1. A customer has a single controller IBM TotalStorage DS4300 Storage Server. What is the maximum numberof expansion drawers that can be attached?
A. 0
B. 3
C. 7
D. 16
Answer: A
2. A customer has a requirement for 9 TB of data to be stored onto tape. If the customer wants the mostcost-effective LTO3 solution, the best technology choice would be:
A. IBM TotalStorage 3581 Tape Autoloader.
B. IBM TotalStorage 3582 Tape Library.
C. IBM TotalStorage 3583 Tape Library.
D. IBM TotalStorage 3584 Tape Library.
Answer: B
3. A customer mentions that they are evaluating Advanced Intelligent Tape (AIT) for their open serverenvironment. Which of the following best describes AIT technology?
A. 4mm
B. Linear recording
C. Helical scan recording
D. IBM TotalStorage 3592 compatible tape
Answer: C
4. A customer needs to limit the total time it takes to back up an existing database. Which of the following isNOT required to understand the customer requirements?
A. The amount of data to be backed up
B. The kind of data being backed up
C. The maximum desired time the backup process should take
D. The number of days backups are scheduled
Answer: D
5. A customer has a heterogeneous environment that is backed up using IBM Tivoli Storage Manager attached to atape silo. Due to network congestion, the expanding data within the environment can no longer be backed upwithin the time available. The data growth is expected to increase rapidly over the next few months. Theaverage recovery window for this environment is currently estimated at 72 hours. Which of the followingoptions would resolve the network problem?
A. Install an IBM TotalStorage NAS Gateway 500.
B. Utilize LAN free backups over the SAN.
C. Install iSCSI to improve block I/O throughput.
D. Increase the number of tape drives within the silo.
Answer: B
1. A customer has a single controller IBM TotalStorage DS4300 Storage Server. What is the maximum numberof expansion drawers that can be attached?
A. 0
B. 3
C. 7
D. 16
Answer: A
2. A customer has a requirement for 9 TB of data to be stored onto tape. If the customer wants the mostcost-effective LTO3 solution, the best technology choice would be:
A. IBM TotalStorage 3581 Tape Autoloader.
B. IBM TotalStorage 3582 Tape Library.
C. IBM TotalStorage 3583 Tape Library.
D. IBM TotalStorage 3584 Tape Library.
Answer: B
3. A customer mentions that they are evaluating Advanced Intelligent Tape (AIT) for their open serverenvironment. Which of the following best describes AIT technology?
A. 4mm
B. Linear recording
C. Helical scan recording
D. IBM TotalStorage 3592 compatible tape
Answer: C
4. A customer needs to limit the total time it takes to back up an existing database. Which of the following isNOT required to understand the customer requirements?
A. The amount of data to be backed up
B. The kind of data being backed up
C. The maximum desired time the backup process should take
D. The number of days backups are scheduled
Answer: D
5. A customer has a heterogeneous environment that is backed up using IBM Tivoli Storage Manager attached to atape silo. Due to network congestion, the expanding data within the environment can no longer be backed upwithin the time available. The data growth is expected to increase rapidly over the next few months. Theaverage recovery window for this environment is currently estimated at 72 hours. Which of the followingoptions would resolve the network problem?
A. Install an IBM TotalStorage NAS Gateway 500.
B. Utilize LAN free backups over the SAN.
C. Install iSCSI to improve block I/O throughput.
D. Increase the number of tape drives within the silo.
Answer: B
Pass4side Oracle 1Z0-033最新考试题库分享（3）
考题内容摘自www.pass4side.cn 更新时间：2008-9-17
11. Smith is a DBA with ABC Corp. He is in the process of tuning the database. He has received various problemstatements from the customers. Identify three appropriately defined problem statements that Smith can use to tunethe database correctly. (Choose three.)
A.The system is too slow.
B.Online response is very slow.
C.Sometimes the batch process throws errors.
D.The weekly backup took 30 minutes, and earlier it used to take 5 minutes.
E.The batch process is taking 2 hours, whereas it should take only 30 minutes.
F.The system currently has 100 users. We wish to increase the number of users to 250. The users’ response timeshould not be affected.
Answer:: DEF
12. Smith is a DBA with XYZ Corp. There are 500 data entry users in an online transaction processing (OLTP)environment. The current response time is 15-20 seconds. The company wants the response time to be broughtdown to 10 seconds or less.What is the first thing that Smith should do to diagnose the cause of the slow response time?
A.determine whether there is contention for locks
B.determine whether the file system is fast enough
C.determine whether more memory needs to be allocated to PGA
D.determine whether more memory needs to be allocated to SGA
E.determine whether the slow response is wait bound or CPU bound
Answer:: E
13. Which two activities would adversely affect database performance? (Choose two.)
A.doing a soft parse
B.performing archiving
C.less frequent checkpointing
D.defining multiple buffer pools
E.taking online back up of data files
Answer:: BE
14. The following are the tasks that you need to perform to create a resource plan:A) Creating resource consumer groupsB) Validating pending areaC) Creating a pending areaD) Creating resource plansE) Creating plan directivesF) Submitting pending areaIn which order would you perform these tasks?
A.C, D, A, E, B, F
B.C, B, F, E, A, D
C.C, B, E, D, A, F
D.C, F, E, A, D, B
Answer:: A
15. View the Exhibit and examine the steps to create a database resource plan. Execution of the followingprocedure resulted in an error:SQL> EXECUTE dbms_resource_manager.validate_pending_area();What could be the reason for this?
A.The ADMINISTER_RESOURCE_MANAGER privilege is not granted to the user.
B.The procedure should be executed before creating the resource plan directive.
C.The SYS_GROUP resource consumer group is not included in the resource plan directive.
D.The OTHER_GROUPS resource consumer group is not included in the resource plan directive.
Answer:: D
11. Smith is a DBA with ABC Corp. He is in the process of tuning the database. He has received various problemstatements from the customers. Identify three appropriately defined problem statements that Smith can use to tunethe database correctly. (Choose three.)
A.The system is too slow.
B.Online response is very slow.
C.Sometimes the batch process throws errors.
D.The weekly backup took 30 minutes, and earlier it used to take 5 minutes.
E.The batch process is taking 2 hours, whereas it should take only 30 minutes.
F.The system currently has 100 users. We wish to increase the number of users to 250. The users’ response timeshould not be affected.
Answer:: DEF
12. Smith is a DBA with XYZ Corp. There are 500 data entry users in an online transaction processing (OLTP)environment. The current response time is 15-20 seconds. The company wants the response time to be broughtdown to 10 seconds or less.What is the first thing that Smith should do to diagnose the cause of the slow response time?
A.determine whether there is contention for locks
B.determine whether the file system is fast enough
C.determine whether more memory needs to be allocated to PGA
D.determine whether more memory needs to be allocated to SGA
E.determine whether the slow response is wait bound or CPU bound
Answer:: E
13. Which two activities would adversely affect database performance? (Choose two.)
A.doing a soft parse
B.performing archiving
C.less frequent checkpointing
D.defining multiple buffer pools
E.taking online back up of data files
Answer:: BE
14. The following are the tasks that you need to perform to create a resource plan:A) Creating resource consumer groupsB) Validating pending areaC) Creating a pending areaD) Creating resource plansE) Creating plan directivesF) Submitting pending areaIn which order would you perform these tasks?
A.C, D, A, E, B, F
B.C, B, F, E, A, D
C.C, B, E, D, A, F
D.C, F, E, A, D, B
Answer:: A
15. View the Exhibit and examine the steps to create a database resource plan. Execution of the followingprocedure resulted in an error:SQL> EXECUTE dbms_resource_manager.validate_pending_area();What could be the reason for this?
A.The ADMINISTER_RESOURCE_MANAGER privilege is not granted to the user.
B.The procedure should be executed before creating the resource plan directive.
C.The SYS_GROUP resource consumer group is not included in the resource plan directive.
D.The OTHER_GROUPS resource consumer group is not included in the resource plan directive.
Answer:: D
Pass4side Oracle 1Z0-033最新考试题库分享（2）
考题内容摘自www.pass4side.cn 更新时间：2008-9-17
6. You have reserved memory within the Shared Pool by using the SHARED_POOL_RESERVED_SIZEparameter to accommodate large space allocations while compiling PL/SQL blocks and database triggers.While observing the performance of the reserved area, you find that the value of the REQUEST_FAILUREScolumn in the V$SHARED_POOL_RESERVED view is continuously increasing.Which statement is true in this scenario?
A.The parsing of the statement fails due to invalidations.
B.The execution of the statement fails due to invalidations.
C.The space allocated for the reserved area is not enough.
D.The syntax in the PL/SQL blocks is causing the compilation failure.
Answer:: C
7. You need to size the KEEP pool. Which calculation would you use to determine the initial size of the KEEPpool?
A.50% of the DEFAULT pool
B.50% of the RECYCLE pool
C.the total number of blocks of all the candidate objects that you need in the KEEP pool / the number of objectsthat you need in the KEEP pool
D.total number of blocks of all the candidate objects that you need in the KEEP pool + additional space to allowfor object growth
Answer:: D
8. ABC Corp. plans to build an online transaction processing (OLTP) system. The company plans to tune all thecomponents during the development life cycle.From the list given below, identify the order in which the components should be tuned.1. logical and physical model2. cursor sharing3. Oracle instance memory structures4. operating system5 data file I/O
A.1, 2, 3, 5, 4
B.1, 3, 2, 4, 5
C.1, 2, 3, 4, 5
D.1, 2, 5, 3, 4
Answer:: A
9. ABC Corp. has an online transaction processing (OLTP) system that has just gone into production. The systemwas rigorously tested during the development phases.What is the first recommended activity that the DBA should perform before starting to monitor the performance ofthe system on a regular basis?A.running SQL*TraceB.collecting baseline statisticsC.analyzing indexes and user tablesD.arranging meetings with users once each two weeks to discuss performanceAnswer:: B10. When tuning a database server, which three goals should you focus on? (Choose three.)
A.minimize response time for OLTP users
B.maximize throughput for batch processing
C.minimize response time for batch processing
D.increase load capability for the decision-support systemsE.minimize parallelism for online transaction processing (OLTP) systems
Answer:: ABD
6. You have reserved memory within the Shared Pool by using the SHARED_POOL_RESERVED_SIZEparameter to accommodate large space allocations while compiling PL/SQL blocks and database triggers.While observing the performance of the reserved area, you find that the value of the REQUEST_FAILUREScolumn in the V$SHARED_POOL_RESERVED view is continuously increasing.Which statement is true in this scenario?
A.The parsing of the statement fails due to invalidations.
B.The execution of the statement fails due to invalidations.
C.The space allocated for the reserved area is not enough.
D.The syntax in the PL/SQL blocks is causing the compilation failure.
Answer:: C
7. You need to size the KEEP pool. Which calculation would you use to determine the initial size of the KEEPpool?
A.50% of the DEFAULT pool
B.50% of the RECYCLE pool
C.the total number of blocks of all the candidate objects that you need in the KEEP pool / the number of objectsthat you need in the KEEP pool
D.total number of blocks of all the candidate objects that you need in the KEEP pool + additional space to allowfor object growth
Answer:: D
8. ABC Corp. plans to build an online transaction processing (OLTP) system. The company plans to tune all thecomponents during the development life cycle.From the list given below, identify the order in which the components should be tuned.1. logical and physical model2. cursor sharing3. Oracle instance memory structures4. operating system5 data file I/O
A.1, 2, 3, 5, 4
B.1, 3, 2, 4, 5
C.1, 2, 3, 4, 5
D.1, 2, 5, 3, 4
Answer:: A
9. ABC Corp. has an online transaction processing (OLTP) system that has just gone into production. The systemwas rigorously tested during the development phases.What is the first recommended activity that the DBA should perform before starting to monitor the performance ofthe system on a regular basis?A.running SQL*TraceB.collecting baseline statisticsC.analyzing indexes and user tablesD.arranging meetings with users once each two weeks to discuss performanceAnswer:: B10. When tuning a database server, which three goals should you focus on? (Choose three.)
A.minimize response time for OLTP users
B.maximize throughput for batch processing
C.minimize response time for batch processing
D.increase load capability for the decision-support systemsE.minimize parallelism for online transaction processing (OLTP) systems
Answer:: ABD
Pass4side Oracle 1Z0-033最新考试题库分享（1）
考题内容摘自www.pass4side.cn 更新时间：2008-9-17
1. You create a stored outline and apply it for use. What strategy would you adopt to verify that the stored outlineis being used for a statement?
A.verify OL$,OL$HINTS, and OL$NODES tables after running the statement with USE_STORED_OUTLINESset
B.examine the V$SQL dynamic performance view after running the statement with theUSE_STORED_OUTLINES set
C.compare the explain plan output for the statement when running with and without theUSE_STORED_OUTLINES set
D.compare the statspack output by taking snaps before and after running the statement with theUSE_STORED_OUTLINES set
Answer:: C
2. View the Exhibit.In your database, you find that the fy05q1 table in a dictionary managed tablespace has excess space. Further, youfind that the table consists of three extents. The size of the first extent is 100KB, the second is 200KB, and thethird is 300K. The high water mark is in the middle of the second extent, and there is 400KB of unused space.You want to release the unused space so that it can be used by other segments. You execute the followingcommand to achieve this task:SQL> ALTER TABLE fy05q1 DEALLOCATE UNUSED;What would this command do?
A.deallocates the third and second extents
B.deallocates the third extent; the second extent remains as it is
C.deallocates the third extent, and the second extent is sized to 100KB
D.returns an error because the unused space is above the high water mark
Answer:: C
3. Why does performance degrade when many UPDATE, INSERT, or DELETE statements are issued on a tablethat has an associated Bitmap index?
A.Some DML operations re-create the Bitmap index blocks.
B.The Bitmap index is rebuilt automatically after a DML operation.
C.The smallest amount of a bitmap that can be locked is a bitmap segment.
D.Additional time is taken to remove NULL values from the Bitmap index after a DML operation.
Answer:: C
4. In an online transaction processing (OLTP) system, you notice that the transactions are waiting. Which twotechniques would you use to determine if it is a locking problem? (Choose two.)
A.query V$SESSION to determine the sessions waiting for locks
B.query V$LOCKED_OBJECT to diagnose the deadlocked sessions
C.execute the utllockt.sql script to find the list of locking and waiting transactions
D.use the catblock.sql script to populate DBA_BLOCKERS and DBA_WAITERS viewsE.query the DBA_WAITERS view to determine the sessions that are waiting for a locked resource
Answer:: CE
5. A customer has various dictionary-managed tablespaces with past data. The extents in dictionary-managedtablespaces are not uniformly sized. Newly created tablespaces are locally managed. You want to make all thetablespaces locally managed. What approach would you use to change the dictionary-managed tablespaces tolocally managed tablespaces to get all the performance benefits of local extent management?
A.use only the DBMS_SPACE_ADMIN.TABLESPACE_MIGRATE_TO_LOCAL procedure
B.create new locally managed tablespaces and move data from existing dictionary-managed tablespaces to locallymanaged tablespaces
C.use the DBMS_SPACE_ADMIN.TABLESPACE_MIGRATE_TO_LOCAL procedure, followed byDBMS_SPACE_ADMIN.TABLESPACE_FIX_SEGMENT_STATES
D.use the ALTER TABLESPACE command to change extent management to local, and then use theDBMS_SPACE_ADMIN.TABLESPACE_MIGRATE_TO_LOCAL procedure
Answer:: B
1. You create a stored outline and apply it for use. What strategy would you adopt to verify that the stored outlineis being used for a statement?
A.verify OL$,OL$HINTS, and OL$NODES tables after running the statement with USE_STORED_OUTLINESset
B.examine the V$SQL dynamic performance view after running the statement with theUSE_STORED_OUTLINES set
C.compare the explain plan output for the statement when running with and without theUSE_STORED_OUTLINES set
D.compare the statspack output by taking snaps before and after running the statement with theUSE_STORED_OUTLINES set
Answer:: C
2. View the Exhibit.In your database, you find that the fy05q1 table in a dictionary managed tablespace has excess space. Further, youfind that the table consists of three extents. The size of the first extent is 100KB, the second is 200KB, and thethird is 300K. The high water mark is in the middle of the second extent, and there is 400KB of unused space.You want to release the unused space so that it can be used by other segments. You execute the followingcommand to achieve this task:SQL> ALTER TABLE fy05q1 DEALLOCATE UNUSED;What would this command do?
A.deallocates the third and second extents
B.deallocates the third extent; the second extent remains as it is
C.deallocates the third extent, and the second extent is sized to 100KB
D.returns an error because the unused space is above the high water mark
Answer:: C
3. Why does performance degrade when many UPDATE, INSERT, or DELETE statements are issued on a tablethat has an associated Bitmap index?
A.Some DML operations re-create the Bitmap index blocks.
B.The Bitmap index is rebuilt automatically after a DML operation.
C.The smallest amount of a bitmap that can be locked is a bitmap segment.
D.Additional time is taken to remove NULL values from the Bitmap index after a DML operation.
Answer:: C
4. In an online transaction processing (OLTP) system, you notice that the transactions are waiting. Which twotechniques would you use to determine if it is a locking problem? (Choose two.)
A.query V$SESSION to determine the sessions waiting for locks
B.query V$LOCKED_OBJECT to diagnose the deadlocked sessions
C.execute the utllockt.sql script to find the list of locking and waiting transactions
D.use the catblock.sql script to populate DBA_BLOCKERS and DBA_WAITERS viewsE.query the DBA_WAITERS view to determine the sessions that are waiting for a locked resource
Answer:: CE
5. A customer has various dictionary-managed tablespaces with past data. The extents in dictionary-managedtablespaces are not uniformly sized. Newly created tablespaces are locally managed. You want to make all thetablespaces locally managed. What approach would you use to change the dictionary-managed tablespaces tolocally managed tablespaces to get all the performance benefits of local extent management?
A.use only the DBMS_SPACE_ADMIN.TABLESPACE_MIGRATE_TO_LOCAL procedure
B.create new locally managed tablespaces and move data from existing dictionary-managed tablespaces to locallymanaged tablespaces
C.use the DBMS_SPACE_ADMIN.TABLESPACE_MIGRATE_TO_LOCAL procedure, followed byDBMS_SPACE_ADMIN.TABLESPACE_FIX_SEGMENT_STATES
D.use the ALTER TABLESPACE command to change extent management to local, and then use theDBMS_SPACE_ADMIN.TABLESPACE_MIGRATE_TO_LOCAL procedure
Answer:: B
Pass4side EMC E20-616 V6.13最新题库（4）
16. How is the Katana number determined on a DMX-800?
A. IMPL bin file
B. Enclosure ID
C. Customer decides
D. FEBE port connection
Answer: D
17. Which command finds the physical location of the M2 of mirrored dev 64?
A. A7,C,64
B. A7,D,64
C. D2,64,0
D. E7,D,64
Answer: B
18. What is the cache slot size on a DMX3?
A. 16K
B. 32K
C. 64K
D. 128K
Answer: C
19. Click the Exhibit button.Where are the daisy chained disks physically located?
A. Lower 2A cabinet
B. Lower 2B cabinet
C. Upper 2A cabinet
D. Upper 2B cabinet
Answer: A
20. Which condition would prevent a spare from invoking on a failing drive?
A. RAID 5 only
B. Parity RAID only
C. All 4 mirror slots are taken
D. None; EMC can spare out everything
Answer: C
A. IMPL bin file
B. Enclosure ID
C. Customer decides
D. FEBE port connection
Answer: D
17. Which command finds the physical location of the M2 of mirrored dev 64?
A. A7,C,64
B. A7,D,64
C. D2,64,0
D. E7,D,64
Answer: B
18. What is the cache slot size on a DMX3?
A. 16K
B. 32K
C. 64K
D. 128K
Answer: C
19. Click the Exhibit button.Where are the daisy chained disks physically located?
A. Lower 2A cabinet
B. Lower 2B cabinet
C. Upper 2A cabinet
D. Upper 2B cabinet
Answer: A
20. Which condition would prevent a spare from invoking on a failing drive?
A. RAID 5 only
B. Parity RAID only
C. All 4 mirror slots are taken
D. None; EMC can spare out everything
Answer: C
Pass4side EMC E20-616 V6.13最新题库（3）
题库内容摘自http://www.pass4side.cn/ 更新时间：2008-9-19
11. Click the Exhibit button.Identify the DMX-1000 memory boards.
A. A
B. B
C. C
D. D
Answer: B
12. What is the benefit of configuring devices as Dynamic SRDF?
A. Control SRDF links
B. Delay D/E to the host
C. Swap SRDF pairs with host software
D. Dynamically change R/W status to the host
Answer: C
13. Which functions are performed by the XCM cards?
A. Communications only
B. Power monitoring only
C. Environmental monitoring only
D. Power monitoring, environmental and communications
Answer: D
14. How many disk operations does Parity RAID do for every host write?
A. 1
B. 2
C. 3
D. 5
Answer: C
15. How many power connections are needed for a 2 bay DMX3?
A. 2
B. 4
C. 6
D. 8
Answer: B
11. Click the Exhibit button.Identify the DMX-1000 memory boards.
A. A
B. B
C. C
D. D
Answer: B
12. What is the benefit of configuring devices as Dynamic SRDF?
A. Control SRDF links
B. Delay D/E to the host
C. Swap SRDF pairs with host software
D. Dynamically change R/W status to the host
Answer: C
13. Which functions are performed by the XCM cards?
A. Communications only
B. Power monitoring only
C. Environmental monitoring only
D. Power monitoring, environmental and communications
Answer: D
14. How many disk operations does Parity RAID do for every host write?
A. 1
B. 2
C. 3
D. 5
Answer: C
15. How many power connections are needed for a 2 bay DMX3?
A. 2
B. 4
C. 6
D. 8
Answer: B
Pass4side EMC E20-616 V6.13最新题库（2）
题库内容摘自www.pass4side.cn 更新时间：2008-9-19
6. After adding Ficon Directors, they do NOT appear as EF in Volumes map. Why?
A. Ficon Directors are automatically addressed
B. Ficon Directors must be added to the host screen
C. Ficon Directors appear as a Split in Volumes map
D. Ficon Directors must be added at Director Edit screen
Answer: C
7. Which PowerPath load balancing policy is used when I/O requests are distributed to each available path in turn?
A. Basic Failover
B. Least I/O
C. Request
D. Round Robin
Answer: D
8. What condition will cause the DMX 3 to vault?
A. Fan module goes out
B. Memory Failure in slot 10
C. Front end cards brought offline
D. Battery time less than 5 minutes
Answer: D
9. Which 8430/8530 card slots are universal?
A. 4,B
B. 5,6
C. 10,11
D. 15,16
Answer: A
10. Which command lists all the WWNs that are logged into port 1?
A. A1,,,1
B. A7,C,1
C. E7,,,1
D. 8F,,,1
Answer: D
6. After adding Ficon Directors, they do NOT appear as EF in Volumes map. Why?
A. Ficon Directors are automatically addressed
B. Ficon Directors must be added to the host screen
C. Ficon Directors appear as a Split in Volumes map
D. Ficon Directors must be added at Director Edit screen
Answer: C
7. Which PowerPath load balancing policy is used when I/O requests are distributed to each available path in turn?
A. Basic Failover
B. Least I/O
C. Request
D. Round Robin
Answer: D
8. What condition will cause the DMX 3 to vault?
A. Fan module goes out
B. Memory Failure in slot 10
C. Front end cards brought offline
D. Battery time less than 5 minutes
Answer: D
9. Which 8430/8530 card slots are universal?
A. 4,B
B. 5,6
C. 10,11
D. 15,16
Answer: A
10. Which command lists all the WWNs that are logged into port 1?
A. A1,,,1
B. A7,C,1
C. E7,,,1
D. 8F,,,1
Answer: D
Pass4side EMC E20-616 V6.13最新题库（1）
题库摘自www.pass4side.cn 网站 更新时间：2008-9-19
1. Which command displays adapter information such as speed capability and adapter type?
A. F0,CE
B. FC,BKAD
C. FC,RLES
D. FC,LINK
Answer: B
2. Which link requires the other box serial number to be entered?
A. FA
B. RA
C. RE
D. RF
Answer: D
3. Which Inlines command displays Invoked Hot spares?
A. A7,HOTS
B. A7,SPARES
C. E7,HOTS
D. E7,SPARES
Answer: A
4. What is the number of vault drive slices for a 2-storage bay, fully configured storage system?A. 16
B. 32
C. 64
D. 128
Answer: D
5. Which command is run from the director to see the I/O statistics on a SA or FA host adapter card?
A. A1,EF
B. A2,BA
C. A2,DA
D. A2,EA
Answer: B
1. Which command displays adapter information such as speed capability and adapter type?
A. F0,CE
B. FC,BKAD
C. FC,RLES
D. FC,LINK
Answer: B
2. Which link requires the other box serial number to be entered?
A. FA
B. RA
C. RE
D. RF
Answer: D
3. Which Inlines command displays Invoked Hot spares?
A. A7,HOTS
B. A7,SPARES
C. E7,HOTS
D. E7,SPARES
Answer: A
4. What is the number of vault drive slices for a 2-storage bay, fully configured storage system?A. 16
B. 32
C. 64
D. 128
Answer: D
5. Which command is run from the director to see the I/O statistics on a SA or FA host adapter card?
A. A1,EF
B. A2,BA
C. A2,DA
D. A2,EA
Answer: B
Pass4side 70-643最新题库DEMO下载
Pass4side 70-647考试题库分享（2）
题库内容摘自www.pass4side.cn 更新时间：2008-9-18更多认证考试题库信息可登陆pass4side网站查看。
6. Your company has a main office and two branch offices. The network contains one Active Directory domain named contoso.com.All domain controllers and DNS servers for the contoso.com domain are located in the main office. All DNS servers are member servers.You plan to deploy two new Active Directory domains named east.contoso.com and west.contoso.com in the branch offices.You install a DNS server in each branch office.You need to prepare the environment for the installation of the new domains.What should you do next?
A. Create a new standard primary zone on each branch office DNS server for the new domains. Configure forwarders on the main office DNS servers to point to the branch office servers.
B. Create a new stub zone on each branch office DNS server for the new domains. Configure conditional forwarders on the main office DNS servers to point to the branch office DNS servers.
C. Configure a delegation subdomain DNS record on the main office DNS server for each new domain. Configure a stub zone on each branch office DNS server for the new domains. Configure zone transfer for the contoso.com zone to the branch office DNS servers.
D. Configure a delegation subdomain DNS record on the main office DNS server for each new domain. Create a new standard primary zone on each branch office DNS server for the new domains. Configure zone transfer for the contoso.com zone to the branch office DNS servers.
Answer: D
7. Your company has one main office and one branch office. The branch office is connected to the main office by using a wide area network (WAN) link. The network consists of one Active directory domain.The branch office has two member servers that run Windows Server 2008. One of the servers is configured as a file server that hosts shared folders.The branch office has a local administrator. The main office has one standard primary DNS zone that is hosted on a DNS server.The branch office grows from 100 client computers to 1,000 client computers.You need to recommend a name resolution solution for the branch office to meet the following requirements:Users must be able to access file shares on the local server if a WAN link fails.The branch office administrator must be able to modify Active Directory objects while at the branch office if a WAN link fails.What should you recommend?
A. Promote the member server to a domain controller and configure the DNS role. Create a standard secondary zone.
B. Promote the member server to a domain controller and configure the DNS role. Create a new standard primary zone.
C. Promote the member server to a read-only domain controller (RODC) and configure the DNS role. Create a primary read-only zone.
D. Promote the member server to a read-only domain controller (RODC) and configure the DNS role. Create a new standard secondary zone.
Answer: A
8. Your network consists of one Active Directory forest that contains one root domain and 22 child domains.All domain controllers run Windows Server 2003. All domain controllers run the DNS Server service and host Active Directory-integrated zones.Administrators report that it takes more than one hour to restart the DNS servers.You need to reduce the time it takes to restart the DNS servers.What should you do?
A. Upgrade all domain controllers to Windows Server 2008.
B. Upgrade all domain controllers in the root domain to Windows Server 2008, and then set the functional level for the root domain to Windows Server 2008.
C. Deploy new secondary zones on additional servers in each child domain.
D. Change the Active Directory-integrated DNS zones to standard primary zones.
Answer: A
9. Your network consists of one Active Directory forest that contains one root domain and 10 child domains.Administrators of the child domains frequently modify the records for authoritative DNS servers for the child domain DNS zones.You need to recommend a solution to minimize the amount of manual configuration steps required to maintain name resolution on the network.What should you recommend?
A. On the child domain DNS servers, create stub zones for the root domain zone.
B. On the child domain DNS servers, configure conditional forwarders for the parent domain.
C. On the root domain DNS servers, create stub zones for the child domain zones.
D. On the root domain DNS servers, configure delegation subdomain records for the child domains.
Answer: C
6. Your company has a main office and two branch offices. The network contains one Active Directory domain named contoso.com.All domain controllers and DNS servers for the contoso.com domain are located in the main office. All DNS servers are member servers.You plan to deploy two new Active Directory domains named east.contoso.com and west.contoso.com in the branch offices.You install a DNS server in each branch office.You need to prepare the environment for the installation of the new domains.What should you do next?
A. Create a new standard primary zone on each branch office DNS server for the new domains. Configure forwarders on the main office DNS servers to point to the branch office servers.
B. Create a new stub zone on each branch office DNS server for the new domains. Configure conditional forwarders on the main office DNS servers to point to the branch office DNS servers.
C. Configure a delegation subdomain DNS record on the main office DNS server for each new domain. Configure a stub zone on each branch office DNS server for the new domains. Configure zone transfer for the contoso.com zone to the branch office DNS servers.
D. Configure a delegation subdomain DNS record on the main office DNS server for each new domain. Create a new standard primary zone on each branch office DNS server for the new domains. Configure zone transfer for the contoso.com zone to the branch office DNS servers.
Answer: D
7. Your company has one main office and one branch office. The branch office is connected to the main office by using a wide area network (WAN) link. The network consists of one Active directory domain.The branch office has two member servers that run Windows Server 2008. One of the servers is configured as a file server that hosts shared folders.The branch office has a local administrator. The main office has one standard primary DNS zone that is hosted on a DNS server.The branch office grows from 100 client computers to 1,000 client computers.You need to recommend a name resolution solution for the branch office to meet the following requirements:Users must be able to access file shares on the local server if a WAN link fails.The branch office administrator must be able to modify Active Directory objects while at the branch office if a WAN link fails.What should you recommend?
A. Promote the member server to a domain controller and configure the DNS role. Create a standard secondary zone.
B. Promote the member server to a domain controller and configure the DNS role. Create a new standard primary zone.
C. Promote the member server to a read-only domain controller (RODC) and configure the DNS role. Create a primary read-only zone.
D. Promote the member server to a read-only domain controller (RODC) and configure the DNS role. Create a new standard secondary zone.
Answer: A
8. Your network consists of one Active Directory forest that contains one root domain and 22 child domains.All domain controllers run Windows Server 2003. All domain controllers run the DNS Server service and host Active Directory-integrated zones.Administrators report that it takes more than one hour to restart the DNS servers.You need to reduce the time it takes to restart the DNS servers.What should you do?
A. Upgrade all domain controllers to Windows Server 2008.
B. Upgrade all domain controllers in the root domain to Windows Server 2008, and then set the functional level for the root domain to Windows Server 2008.
C. Deploy new secondary zones on additional servers in each child domain.
D. Change the Active Directory-integrated DNS zones to standard primary zones.
Answer: A
9. Your network consists of one Active Directory forest that contains one root domain and 10 child domains.Administrators of the child domains frequently modify the records for authoritative DNS servers for the child domain DNS zones.You need to recommend a solution to minimize the amount of manual configuration steps required to maintain name resolution on the network.What should you recommend?
A. On the child domain DNS servers, create stub zones for the root domain zone.
B. On the child domain DNS servers, configure conditional forwarders for the parent domain.
C. On the root domain DNS servers, create stub zones for the child domain zones.
D. On the root domain DNS servers, configure delegation subdomain records for the child domains.
Answer: C
Pass4side 70-647考试题库分享（1）
题库内容摘自www.pass4side.cn 更新时间：2008-9-18
更多认证考试题库信息可登陆pass4side网站查看。
1. Your company has a main office and a new branch office. The network consists of one Active directory domain.The branch office contains two member servers that run Windows Server 2008. One of the servers is configured as a file server that hosts shared folders. An administrator in the branch office is responsible for maintaining the servers.You have a single DNS zone that is hosted on a DNS server located in the main office.A wide area network (WAN) link between the branch office and the main office is unreliable.You need to recommend a network services solution for the new branch office. The solution must meet the following requirements:Users must be able to log on to the domain if a WAN link fails.Users must be able to access file shares on the local server if a WAN link fails.Branch office administrators must be prevented from initiating changes to Active Directory.Branch office administrators must be able to make configuration changes to the servers in the branch office.What should you recommend?A. Promote the member server to a domain controller and add the branch office administrators to the Domain Admins group.
B. Promote the member server to a read-only domain controller (RODC) and add the branch office administrators to the Domain Admins group.
C. Promote the member server to a read-only domain controller (RODC) and configure the DNS role. Delegate administrative rights to the local branch office administrator.
D. Promote the member server to a domain controller and configure the DNS role. Create an organizational unit (OU) for each branch office and delegate administrative rights to the local branch office administrator.
Answer: C
2. Your company has one office in San Diego and one office in New York.The network consists of one Active Directory forest that contains one domain named contoso.com and one domain named newyork.contoso.com. All servers run Windows Server 2008. All domain controllers for contoso.com are located in San Diego. All domain controllers for newyork.contoso.com are located in New York.Contoso.com contains two domain controllers named Server1 and Server2. Newyork.contoso.com contains two domain controllers named Server3 and Server4. All domain controllers host Active Directory-integrated DNS zones for their respective domains.You need to ensure that users from each office can resolve computer names for both domains from a local DNS server.What should you do?
A. Add the contoso.com and the newyork.contoso.com DNS zones to the ForestDNSZones partition.
B. Create a stub DNS zone for contoso.com on Server3. Create a stub DNS zone for newyork.contoso.com on Server1.
C. Create a standard primary DNS zone named contoso.com on Server3. Create a standard primary DNS zone named newyork.contoso.com on Server1.
D. Configure conditional forwarders on Server1 to point to Server3. Configure conditional forwarders on Server3 to point to Server1.
Answer: A
3. Your company has a main office and three branch offices.Each office has a server that runs Windows Server 2008. The server has the DNS Server role installed. The branch offices contain client computers that run Windows 2000.You plan to deploy Active Directory Domain Services (AD DS) on the network.You need to plan a name resolution solution for the deployment of Active Directory Domain Services (AD DS).The solution must meet the following requirements:Support secure dynamic updates.Minimize response times for users connecting to resources anywhere on the network.What should you include in your plan?
A. A GlobalNames zone for the forest.
B. A single Active Directory-integrated DNS zone.
C. A stub zone on the DNS server in each branch office.
D. A standard primary zone in the main office and secondary zones in each branch office.
Answer: B
4. Your company has one office in Montreal and one office in New York. Each office has 2,000 client computers configured as DHCP clients. DHCP relay is not supported on the network routers.The network consists of one Active Directory domain.You need to recommend a DHCP addressing solution for both offices. The solution must meet the following requirements:Minimize traffic between offices.Be available if a single server fails.What should you recommend?
A. In each office, install a DHCP server that has two scopes.
B. In each office, install a DHCP instance on a two node failover cluster.
C. In the Montreal office, install a DHCP server. In the New York office, install a DHCP Relay Agent.
D. In the Montreal office, install a DHCP instance on a two node failover cluster. In the New York office, install a DHCP Relay Agent.
Answer: B
5. Your network consists of one Active Directory forest that contains 20 domain trees. All DNS servers run Windows Server 2008. The network is configured as an IPv4 network.Users connect to network applications in all domains by using a NetBIOS name.You plan to migrate to an IPv6-enabled only network.You need to recommend a solution to migrate the network to IPv6. The solution must not require any changes to client computers.What should you recommend?
A. On the DNS servers, configure GlobalNames zones.
B. On the DNS servers, add all domain zones to the ForestDNSZones partition.
C. On a new server, install and configure a Windows Server 2008 WINS server.
D. On a new server, install and configure a Windows Server 2003 WINS server.
Answer: A
更多认证考试题库信息可登陆pass4side网站查看。
1. Your company has a main office and a new branch office. The network consists of one Active directory domain.The branch office contains two member servers that run Windows Server 2008. One of the servers is configured as a file server that hosts shared folders. An administrator in the branch office is responsible for maintaining the servers.You have a single DNS zone that is hosted on a DNS server located in the main office.A wide area network (WAN) link between the branch office and the main office is unreliable.You need to recommend a network services solution for the new branch office. The solution must meet the following requirements:Users must be able to log on to the domain if a WAN link fails.Users must be able to access file shares on the local server if a WAN link fails.Branch office administrators must be prevented from initiating changes to Active Directory.Branch office administrators must be able to make configuration changes to the servers in the branch office.What should you recommend?A. Promote the member server to a domain controller and add the branch office administrators to the Domain Admins group.
B. Promote the member server to a read-only domain controller (RODC) and add the branch office administrators to the Domain Admins group.
C. Promote the member server to a read-only domain controller (RODC) and configure the DNS role. Delegate administrative rights to the local branch office administrator.
D. Promote the member server to a domain controller and configure the DNS role. Create an organizational unit (OU) for each branch office and delegate administrative rights to the local branch office administrator.
Answer: C
2. Your company has one office in San Diego and one office in New York.The network consists of one Active Directory forest that contains one domain named contoso.com and one domain named newyork.contoso.com. All servers run Windows Server 2008. All domain controllers for contoso.com are located in San Diego. All domain controllers for newyork.contoso.com are located in New York.Contoso.com contains two domain controllers named Server1 and Server2. Newyork.contoso.com contains two domain controllers named Server3 and Server4. All domain controllers host Active Directory-integrated DNS zones for their respective domains.You need to ensure that users from each office can resolve computer names for both domains from a local DNS server.What should you do?
A. Add the contoso.com and the newyork.contoso.com DNS zones to the ForestDNSZones partition.
B. Create a stub DNS zone for contoso.com on Server3. Create a stub DNS zone for newyork.contoso.com on Server1.
C. Create a standard primary DNS zone named contoso.com on Server3. Create a standard primary DNS zone named newyork.contoso.com on Server1.
D. Configure conditional forwarders on Server1 to point to Server3. Configure conditional forwarders on Server3 to point to Server1.
Answer: A
3. Your company has a main office and three branch offices.Each office has a server that runs Windows Server 2008. The server has the DNS Server role installed. The branch offices contain client computers that run Windows 2000.You plan to deploy Active Directory Domain Services (AD DS) on the network.You need to plan a name resolution solution for the deployment of Active Directory Domain Services (AD DS).The solution must meet the following requirements:Support secure dynamic updates.Minimize response times for users connecting to resources anywhere on the network.What should you include in your plan?
A. A GlobalNames zone for the forest.
B. A single Active Directory-integrated DNS zone.
C. A stub zone on the DNS server in each branch office.
D. A standard primary zone in the main office and secondary zones in each branch office.
Answer: B
4. Your company has one office in Montreal and one office in New York. Each office has 2,000 client computers configured as DHCP clients. DHCP relay is not supported on the network routers.The network consists of one Active Directory domain.You need to recommend a DHCP addressing solution for both offices. The solution must meet the following requirements:Minimize traffic between offices.Be available if a single server fails.What should you recommend?
A. In each office, install a DHCP server that has two scopes.
B. In each office, install a DHCP instance on a two node failover cluster.
C. In the Montreal office, install a DHCP server. In the New York office, install a DHCP Relay Agent.
D. In the Montreal office, install a DHCP instance on a two node failover cluster. In the New York office, install a DHCP Relay Agent.
Answer: B
5. Your network consists of one Active Directory forest that contains 20 domain trees. All DNS servers run Windows Server 2008. The network is configured as an IPv4 network.Users connect to network applications in all domains by using a NetBIOS name.You plan to migrate to an IPv6-enabled only network.You need to recommend a solution to migrate the network to IPv6. The solution must not require any changes to client computers.What should you recommend?
A. On the DNS servers, configure GlobalNames zones.
B. On the DNS servers, add all domain zones to the ForestDNSZones partition.
C. On a new server, install and configure a Windows Server 2008 WINS server.
D. On a new server, install and configure a Windows Server 2003 WINS server.
Answer: A
Pass4side全真MB4-535考试认证题库分享（2）
题库摘自www.pass4side.cn 。 更新时间：2008-9-16
11. How many ledgers can be affected by a single Journal Transactions batch?
A. One
B. One ledger per transaction line
C. One ledger per transaction line, as long as debits equal credits for each ledger in the batch
D. Unlimited
Answer: A
12. Which batch status values will post during the Post Transactions process?
A. Unposted
B. Hold
C. Balanced
D. Posted
Answer: A
13. Which “Account Types” are recognized by Microsoft Dynamics SL?
A. Asset, Liability, Revenue only
B. Asset, Liability, Income, Expense
C. Asset, Payable, Receivable, Expense
D. Any account type can be assigned
Answer: B
14. Which fiscal periods can be entered as the Period to Post in the Journal transactions screen? Choose the 3that apply.A. Any Future PeriodB. Any period in the current fiscal yearC. Any prior period in any year.D. Any prior period as far back as the General Ledger history retention settings.Answer: ABD15. In which periods will transactions update account balances when the Post Transactions process is run?Choose the 2 that apply.
A. Current period
B. Future periods
C. Prior periods
D. Only periods that have not had transactions posted yet.
Answer: AC
16. Which ledger type is used to track the number of employees associated with each payroll expense account?
A. Budget
B. Statistical
C. Actual
D. Reporting Currency
Answer: B
17. A company wishes to segment their subaccount as follows: 1. Company Segment, 2. Location, 3.Department, 4. Event, 5. Region, 6. Project, 7. Sales Type. How is this accomplished?
A. Define the Subaccount as seven Segments in Flexkey Definition.
B. Recommend the company not use Solomon as the subaccount does not accommodate this scenario.
C. Recommend the client use three segments as seven is just too many.
D. Define one of the segments as part of the natural account and create a subaccount with six segments.
Answer: A
18. When is the “Adjustment” batch type used?
A. Correct a batch of transactions entered in error
B. Link a corrected batch to an original batch
C. Enter statistical transactions
D. Make a one-sided journal entry
Answer: D
19. Which scenarios would require a new Budget distribution with assigned percentages? Choose the 2 thatapply.
A. Seasonal variations for employee expenses.
B. Equally distribute expenses for office supplies.
C. Monthly variation for utilities.
D. Distribute an expense based on the actual balances for the prior year.
Answer: AC
20. Which ledger do transactions from Accounts Payable update?
A. Any Actual type of ledger
B. Any Statistical type of ledger
C. Only the ledger in the “Default Ledger ID” field in the GL setup screen
D. Any Budget Ledger
Answer: C
11. How many ledgers can be affected by a single Journal Transactions batch?
A. One
B. One ledger per transaction line
C. One ledger per transaction line, as long as debits equal credits for each ledger in the batch
D. Unlimited
Answer: A
12. Which batch status values will post during the Post Transactions process?
A. Unposted
B. Hold
C. Balanced
D. Posted
Answer: A
13. Which “Account Types” are recognized by Microsoft Dynamics SL?
A. Asset, Liability, Revenue only
B. Asset, Liability, Income, Expense
C. Asset, Payable, Receivable, Expense
D. Any account type can be assigned
Answer: B
14. Which fiscal periods can be entered as the Period to Post in the Journal transactions screen? Choose the 3that apply.A. Any Future PeriodB. Any period in the current fiscal yearC. Any prior period in any year.D. Any prior period as far back as the General Ledger history retention settings.Answer: ABD15. In which periods will transactions update account balances when the Post Transactions process is run?Choose the 2 that apply.
A. Current period
B. Future periods
C. Prior periods
D. Only periods that have not had transactions posted yet.
Answer: AC
16. Which ledger type is used to track the number of employees associated with each payroll expense account?
A. Budget
B. Statistical
C. Actual
D. Reporting Currency
Answer: B
17. A company wishes to segment their subaccount as follows: 1. Company Segment, 2. Location, 3.Department, 4. Event, 5. Region, 6. Project, 7. Sales Type. How is this accomplished?
A. Define the Subaccount as seven Segments in Flexkey Definition.
B. Recommend the company not use Solomon as the subaccount does not accommodate this scenario.
C. Recommend the client use three segments as seven is just too many.
D. Define one of the segments as part of the natural account and create a subaccount with six segments.
Answer: A
18. When is the “Adjustment” batch type used?
A. Correct a batch of transactions entered in error
B. Link a corrected batch to an original batch
C. Enter statistical transactions
D. Make a one-sided journal entry
Answer: D
19. Which scenarios would require a new Budget distribution with assigned percentages? Choose the 2 thatapply.
A. Seasonal variations for employee expenses.
B. Equally distribute expenses for office supplies.
C. Monthly variation for utilities.
D. Distribute an expense based on the actual balances for the prior year.
Answer: AC
20. Which ledger do transactions from Accounts Payable update?
A. Any Actual type of ledger
B. Any Statistical type of ledger
C. Only the ledger in the “Default Ledger ID” field in the GL setup screen
D. Any Budget Ledger
Answer: C
Pass4side全真MB4-535考试认证题库分享（1）
文章摘自www.pass4side.cn 。 更新时间：2008-9-16
1. What occurs in the system when General Ledger is closed for a period and the Delete Detail box is checked?Choose the 2 that apply.
A. The Period to Post field defaults to the next period in the Journal Transaction screen.
B. A transaction is created to post the difference between income and expense accounts to the Net Incomeaccount.
C. Detail is deleted based on GL Setup retention settings.
D. The period being closed is flagged as “Closed” and no additional batches may be entered for that period.
Answer: AC
2. Which Allocation Method is used to allocate office supplies posted to an administrative account to eachdepartment based on the amount of office supply expense in each departmental subaccount?
A. Actual Period-to-Date
B. Ledger-Period-to-Date
C. Percent
D. Unit Ratio
Answer: A
3. Which of the following functions would save data entry time if a user inputs a similar journal entry eachmonth?
A. Manual or Recurring batch
B. Consolidation batch
C. Allocation Group
D. Adjustment batch
Answer: A
4. General Ledger transaction and account history detail is being retained for one year. General Ledger wasclosed for the year in period 12-2005 and the Delete Detail option was checked. Which of the followingfunctions may still be performed? Choose the 3 that apply.
A. Print a Trial Balance Report for period 01-2005.
B. Inquire on account balances for period 06-2005.
C. Enter a batch to post to period 12-2005.
D. Enter a batch to post to period 12-2003.
Answer: ABC
5. What determines the fiscal period for posting a transaction?
A. Current fiscal period value from the GL Setup screen
B. Transaction Date
C. Current business date
D. Period to Post in the data entry screen
Answer: D
6. Which of the following functions can be accomplished in the General Ledger Closing screen? Choose the 3that apply.
A. Close particular modules or all modules for the Period.
B. Close particular modules or all modules for the Year.
C. Delete detail for one or more modules.
D. Re-open a prior period so additional transactions can be entered.
Answer: ABC
7. The option “Edit only in Init Mode” is checked in GL Setup. How do you edit a General Ledger batch that is“Released” but not “Posted”?
A. The “Released” batch cannot be edited.
B. Any batch is always available for editing.
C. Use Initialize Mode to edit the batch.
D. Change the status to “Unreleased” and edit the batch.
Answer: C
8. How do you change the Default Ledger ID specified in the GL Setup screen?
A. Use Initialize Mode
B. The field can be changed at any time.
C. Once set, this field cannot be changed.
D. Use Customization Manager
Answer: C
9. In Flexkey Definition, the “Validate” option for each segment is not checked and the “Valid Combos Required”option is not checked. Which will occur during maintenance and data entry? Choose the 2 that apply.
A. There will be limited account/subaccount combinations available for data entry.
B. When setting up new subaccounts, any value may be entered for any segment.
C. It will not be necessary to enter a subaccount during data entry.
D. All subaccounts entered during data entry will be accepted and automatically created in SubaccountMaintenance.
Answer: BD
10. A batch was posted to period 03-2007 and should have been posted to period 02-2007. Which steps arerequired to correct the situation? Choose the 2 that apply.
A. Enter a batch with the same debits and credits as the original and post it to period 03-2007.
B. Edit the Period to Post on the original batch and run the Post Transactions process again.
C. Enter a batch with the opposite debits and credits and post it to period 03-2007.
D. Enter a batch with the same debits and credits as the original and post it to period 02-2007.Answer: CD
1. What occurs in the system when General Ledger is closed for a period and the Delete Detail box is checked?Choose the 2 that apply.
A. The Period to Post field defaults to the next period in the Journal Transaction screen.
B. A transaction is created to post the difference between income and expense accounts to the Net Incomeaccount.
C. Detail is deleted based on GL Setup retention settings.
D. The period being closed is flagged as “Closed” and no additional batches may be entered for that period.
Answer: AC
2. Which Allocation Method is used to allocate office supplies posted to an administrative account to eachdepartment based on the amount of office supply expense in each departmental subaccount?
A. Actual Period-to-Date
B. Ledger-Period-to-Date
C. Percent
D. Unit Ratio
Answer: A
3. Which of the following functions would save data entry time if a user inputs a similar journal entry eachmonth?
A. Manual or Recurring batch
B. Consolidation batch
C. Allocation Group
D. Adjustment batch
Answer: A
4. General Ledger transaction and account history detail is being retained for one year. General Ledger wasclosed for the year in period 12-2005 and the Delete Detail option was checked. Which of the followingfunctions may still be performed? Choose the 3 that apply.
A. Print a Trial Balance Report for period 01-2005.
B. Inquire on account balances for period 06-2005.
C. Enter a batch to post to period 12-2005.
D. Enter a batch to post to period 12-2003.
Answer: ABC
5. What determines the fiscal period for posting a transaction?
A. Current fiscal period value from the GL Setup screen
B. Transaction Date
C. Current business date
D. Period to Post in the data entry screen
Answer: D
6. Which of the following functions can be accomplished in the General Ledger Closing screen? Choose the 3that apply.
A. Close particular modules or all modules for the Period.
B. Close particular modules or all modules for the Year.
C. Delete detail for one or more modules.
D. Re-open a prior period so additional transactions can be entered.
Answer: ABC
7. The option “Edit only in Init Mode” is checked in GL Setup. How do you edit a General Ledger batch that is“Released” but not “Posted”?
A. The “Released” batch cannot be edited.
B. Any batch is always available for editing.
C. Use Initialize Mode to edit the batch.
D. Change the status to “Unreleased” and edit the batch.
Answer: C
8. How do you change the Default Ledger ID specified in the GL Setup screen?
A. Use Initialize Mode
B. The field can be changed at any time.
C. Once set, this field cannot be changed.
D. Use Customization Manager
Answer: C
9. In Flexkey Definition, the “Validate” option for each segment is not checked and the “Valid Combos Required”option is not checked. Which will occur during maintenance and data entry? Choose the 2 that apply.
A. There will be limited account/subaccount combinations available for data entry.
B. When setting up new subaccounts, any value may be entered for any segment.
C. It will not be necessary to enter a subaccount during data entry.
D. All subaccounts entered during data entry will be accepted and automatically created in SubaccountMaintenance.
Answer: BD
10. A batch was posted to period 03-2007 and should have been posted to period 02-2007. Which steps arerequired to correct the situation? Choose the 2 that apply.
A. Enter a batch with the same debits and credits as the original and post it to period 03-2007.
B. Edit the Period to Post on the original batch and run the Post Transactions process again.
C. Enter a batch with the opposite debits and credits and post it to period 03-2007.
D. Enter a batch with the same debits and credits as the original and post it to period 02-2007.Answer: CD
Pass4side 70-431最新考试题库DEMO分享（2）
本题库摘自www.pass4side.cn 更新时间：2008-9-17更多考试题库信息可登陆查看。
6. A support engineer reports that inserting new sales transactions in a SQL Server 2005 database results in anerror. You investigate the error. You discover that in one of the databases, a developer has accidentally deletedsome data in a table that is critical for transaction processing. The database uses the full recovery model. You needto restore the table. You need to achieve this goal without affecting the availability of other data in the database.What should you do?
A. Back up the current transaction log. Restore the database with a different name and stop at the point just beforethe data loss. Copy the table back into the original database.
B. Back up the current transaction log. Restore the database to the point just before the data loss.
C. Restore the database from the existing backup files to a time just before the data loss.
D. Restore the database to the point of the last full backup.
Answer: A
7. Your company uses SQL Server 2005. Users report that report execution is slow. You investigate and discoverthat some queries do not use optimal execution plans. You also notice that some optimizer statistics are missingand others are out of date. You need to correct the problem so that reports execute more quickly. Which twoTransact-SQL statements should you use? (Each correct answer presents part of the solution. Choose two.)
A. DBCC CHECKTABLE
B. ALTER INDEX REORGANIZE
C. UPDATE STATISTICS
D. CREATE STATISTICS
E. DBCC SHOW_STATISTICS
F. DBCC UPDATEUSAGE
Answer: CD
8. You are responsible for implementing maintenance jobs on a SQL Server 2005 database server. Certain jobs runevery Sunday and other jobs run at the beginning of every month. You need to schedule the jobs in the way thatuses the least amount of administrative effort. What should you do?
A. Create a job schedule that runs every Sunday. Assign weekly tasks to this schedule. Create a second schedulethat runs on the first day of every month. Assign monthly tasks to this schedule.
B. Create a job for each task that runs once a day. Use a Transact-SQL statement to check the date and day of theweek. If the day is either a Sunday or the first day of the month, execute the code.
C. Create a job schedule that runs once a day. Assign jobs to this job schedule. If the day is either a Sunday or thefirst day of the month, execute the jobs.
D. Create a job for each task that runs once a week on Sunday. Add a second job schedule that runs the job on thefirst of the month.
Answer: A
9. You are responsible for managing the database schema for an order entry application in a SQL Server 2005database. After a design review, a member of the development staff asks you to add a new column namedCommissionRate to the Product table. Because the actual commission rates for all products are not known at thistime, each product has a default commission rate of 12 percent. The rate can be modified as necessary. You addthe new column. You need to configure the table to assign the default value as efficiently as possible. What shouldyou do?
A. Create an INSERT trigger to assign the default value to each item in the table.
B. Create a CHECK constraint to validate the data and to assign the default value to each item in the table.
6. A support engineer reports that inserting new sales transactions in a SQL Server 2005 database results in anerror. You investigate the error. You discover that in one of the databases, a developer has accidentally deletedsome data in a table that is critical for transaction processing. The database uses the full recovery model. You needto restore the table. You need to achieve this goal without affecting the availability of other data in the database.What should you do?
A. Back up the current transaction log. Restore the database with a different name and stop at the point just beforethe data loss. Copy the table back into the original database.
B. Back up the current transaction log. Restore the database to the point just before the data loss.
C. Restore the database from the existing backup files to a time just before the data loss.
D. Restore the database to the point of the last full backup.
Answer: A
7. Your company uses SQL Server 2005. Users report that report execution is slow. You investigate and discoverthat some queries do not use optimal execution plans. You also notice that some optimizer statistics are missingand others are out of date. You need to correct the problem so that reports execute more quickly. Which twoTransact-SQL statements should you use? (Each correct answer presents part of the solution. Choose two.)
A. DBCC CHECKTABLE
B. ALTER INDEX REORGANIZE
C. UPDATE STATISTICS
D. CREATE STATISTICS
E. DBCC SHOW_STATISTICS
F. DBCC UPDATEUSAGE
Answer: CD
8. You are responsible for implementing maintenance jobs on a SQL Server 2005 database server. Certain jobs runevery Sunday and other jobs run at the beginning of every month. You need to schedule the jobs in the way thatuses the least amount of administrative effort. What should you do?
A. Create a job schedule that runs every Sunday. Assign weekly tasks to this schedule. Create a second schedulethat runs on the first day of every month. Assign monthly tasks to this schedule.
B. Create a job for each task that runs once a day. Use a Transact-SQL statement to check the date and day of theweek. If the day is either a Sunday or the first day of the month, execute the code.
C. Create a job schedule that runs once a day. Assign jobs to this job schedule. If the day is either a Sunday or thefirst day of the month, execute the jobs.
D. Create a job for each task that runs once a week on Sunday. Add a second job schedule that runs the job on thefirst of the month.
Answer: A
9. You are responsible for managing the database schema for an order entry application in a SQL Server 2005database. After a design review, a member of the development staff asks you to add a new column namedCommissionRate to the Product table. Because the actual commission rates for all products are not known at thistime, each product has a default commission rate of 12 percent. The rate can be modified as necessary. You addthe new column. You need to configure the table to assign the default value as efficiently as possible. What shouldyou do?
A. Create an INSERT trigger to assign the default value to each item in the table.
B. Create a CHECK constraint to validate the data and to assign the default value to each item in the table.
Pass4side 70-431最新考试题库DEMO分享（1）
题库摘自：www.pass4side.cn 更新时间：2008-9-17
1. Your company, Contoso, Ltd., has a main office and a branch officE. The offices are connected by a WAN link.Contoso has an Active Directory forest that contains a single domain named ad.contoso.com.The ad.contoso.com domain contains one domain controller named DC1 that is located in the main officE. DC1 isconfigured as a DNS server for the ad.contoso.com DNS zon
E. This zone is configured as a standard primaryzone.You install a new domain controller named DC2 in the branch officE. You install DNS on DC2.You need to ensure that the DNS service can update records and resolve DNS queries in the event that a WAN linkfails.What should you do?A. Create a new stub zone named ad.contoso.com on DC2.
B. Configure the DNS server on DC2 to forward requests to DC1.
C. Create a new standard secondary zone named ad.contoso.com on DC2.
D. Convert the ad.contoso.com zone on DC1 to an Active Directory-integrated zone.
Answer: D
2. Your company has a DNS server that has 10 Active Directory integrated zones.You need to provide copies of the zone files of the DNS server to the security department.What should you do?
A. Run the dnscmd /ZoneInfo command.
B. Run the ipconfig /registerdns command.
C. Run the dnscmd /ZoneExport command.
D. Run the ntdsutil > Partition Management > List commands.
Answer: C
3. Your company has a single Active Directory domain named intranet.adatum.com. The domain controllers runWindows Server 2008 and the DNS server rolE.All computers, including non-domain members, dynamically register their DNS records.You need to configure the intranet.adatum.com zone to allow only domain members to dynamically register DNSrecords.What should you do?
A. Set dynamic updates to Secure Only.
B. Enable zone transfers to Name Servers.
C. Remove the Authenticated Users group.
D. Deny the Everyone group the Create All Child Objects permission.
Answer: A
4. Your company has a main office and a branch officE. The company has a single-domain Active Directoryforest.The main office has two domain controllers named DC1 and DC2 that run Windows Server 2008. The branchoffice has a Windows Server 2008 read-only domain controller (RODC) named DC3.All domain controllers hold the DNS Server server role and are configured as Active Directory-integrated zones.The DNS zones only allow secure updates.You need to enable dynamic DNS updates on DC3.What should you do?
A. Run the Ntdsutil.exe > DS Behavior commands on DC3.
B. Run the Dnscmd.exe /ZoneResetType command on DC3.
C. Reinstall Active Directory Domain Services on DC3 as a writable domain controller.
D. Create a custom application directory partition on DC1. Configure the partition to store ActiveDirectory-integrated zones.
Answer: C
5. You have a single Active Directory domain. All domain controllers run Windows Server 2008 and areconfigured as DNS servers. The domain contains one Active Directory-integrated DNS zone.You need to ensure that outdated DNS records are automatically removed from the DNS zone.What should you do?
A. From the properties of the zone, enable scavenging.
B. From the properties of the zone, disable dynamic updates.
C. From the properties of the zone, modify the TTL of the SOA record.
D. From the command prompt, run ipconfig /flushdns.
Answer: A
1. Your company, Contoso, Ltd., has a main office and a branch officE. The offices are connected by a WAN link.Contoso has an Active Directory forest that contains a single domain named ad.contoso.com.The ad.contoso.com domain contains one domain controller named DC1 that is located in the main officE. DC1 isconfigured as a DNS server for the ad.contoso.com DNS zon
E. This zone is configured as a standard primaryzone.You install a new domain controller named DC2 in the branch officE. You install DNS on DC2.You need to ensure that the DNS service can update records and resolve DNS queries in the event that a WAN linkfails.What should you do?A. Create a new stub zone named ad.contoso.com on DC2.
B. Configure the DNS server on DC2 to forward requests to DC1.
C. Create a new standard secondary zone named ad.contoso.com on DC2.
D. Convert the ad.contoso.com zone on DC1 to an Active Directory-integrated zone.
Answer: D
2. Your company has a DNS server that has 10 Active Directory integrated zones.You need to provide copies of the zone files of the DNS server to the security department.What should you do?
A. Run the dnscmd /ZoneInfo command.
B. Run the ipconfig /registerdns command.
C. Run the dnscmd /ZoneExport command.
D. Run the ntdsutil > Partition Management > List commands.
Answer: C
3. Your company has a single Active Directory domain named intranet.adatum.com. The domain controllers runWindows Server 2008 and the DNS server rolE.All computers, including non-domain members, dynamically register their DNS records.You need to configure the intranet.adatum.com zone to allow only domain members to dynamically register DNSrecords.What should you do?
A. Set dynamic updates to Secure Only.
B. Enable zone transfers to Name Servers.
C. Remove the Authenticated Users group.
D. Deny the Everyone group the Create All Child Objects permission.
Answer: A
4. Your company has a main office and a branch officE. The company has a single-domain Active Directoryforest.The main office has two domain controllers named DC1 and DC2 that run Windows Server 2008. The branchoffice has a Windows Server 2008 read-only domain controller (RODC) named DC3.All domain controllers hold the DNS Server server role and are configured as Active Directory-integrated zones.The DNS zones only allow secure updates.You need to enable dynamic DNS updates on DC3.What should you do?
A. Run the Ntdsutil.exe > DS Behavior commands on DC3.
B. Run the Dnscmd.exe /ZoneResetType command on DC3.
C. Reinstall Active Directory Domain Services on DC3 as a writable domain controller.
D. Create a custom application directory partition on DC1. Configure the partition to store ActiveDirectory-integrated zones.
Answer: C
5. You have a single Active Directory domain. All domain controllers run Windows Server 2008 and areconfigured as DNS servers. The domain contains one Active Directory-integrated DNS zone.You need to ensure that outdated DNS records are automatically removed from the DNS zone.What should you do?
A. From the properties of the zone, enable scavenging.
B. From the properties of the zone, disable dynamic updates.
C. From the properties of the zone, modify the TTL of the SOA record.
D. From the command prompt, run ipconfig /flushdns.
Answer: A
H3C各种型号交换机端口镜像配置方法总结
一、端口镜像概念：Port Mirror(端口镜像）是用于进行网络性能监测。可以这样理解：在端口A 和端口B 之间建立镜像关系，这样，通过端口A 传输的数据将同时复制到端口B ，以便于在端口B 上连接的分析仪或者分析软件进行性能分析或故障判断。二、端口镜像配置『环境配置参数』
1. PC1接在交换机E0/1端口，IP地址1.1.1.1/242. PC2接在交换机E0/2端口，IP地址2.2.2.2/243. E0/24为交换机上行端口4. Server接在交换机E0/8端口，该端口作为镜像端口『组网需求』1. 通过交换机端口镜像的功能使用server对两台pc的业务报文进行监控。
2. 按照镜像的不同方式进行配置：1) 基于端口的镜像2) 基于流的镜像2 数据配置步骤『端口镜像的数据流程』基于端口的镜像是把被镜像端口的进出数据报文完全拷贝一份到镜像端口，这样来进行流量观测或者故障定位。
【3026等交换机镜像】S2008/S2016/S2026/S2403H/S3026等交换机支持的都是基于端口的镜像，有两种方法：方法一1. 配置镜像（观测）端口[SwitchA]monitor-port e0/82. 配置被镜像端口[SwitchA]port mirror Ethernet 0/1 to Ethernet 0/2方法二1. 可以一次性定义镜像和被镜像端口[SwitchA]port mirror Ethernet 0/1 to Ethernet 0/2 observing-port Ethernet 0/8
【8016交换机端口镜像配置】1. 假设8016交换机镜像端口为E1/0/15，被镜像端口为E1/0/0，设置端口1/0/15为端口镜像的观测端口。[SwitchA] port monitor ethernet 1/0/152. 设置端口1/0/0为被镜像端口，对其输入输出数据都进行镜像。[SwitchA] port mirroring ethernet 1/0/0 both ethernet 1/0/15也可以通过两个不同的端口，对输入和输出的数据分别镜像1. 设置E1/0/15和E2/0/0为镜像（观测）端口[SwitchA] port monitor ethernet 1/0/152. 设置端口1/0/0为被镜像端口，分别使用E1/0/15和E2/0/0对输入和输出数据进行镜像。[SwitchA] port mirroring gigabitethernet 1/0/0 ingress ethernet 1/0/15[SwitchA] port mirroring gigabitethernet 1/0/0 egress ethernet 2/0/0『基于流镜像的数据流程』基于流镜像的交换机针对某些流进行镜像，每个连接都有两个方向的数据流，对于交换机来说这两个数据流是要分开镜像的。【3500/3026E/3026F/3050】〖基于三层流的镜像〗1. 定义一条扩展访问控制列表[SwitchA]acl num 1002. 定义一条规则报文源地址为1.1.1.1/32去往所有目的地址[SwitchA-acl-adv-101]rule 0 permit ip source 1.1.1.1 0 destination any3. 定义一条规则报文源地址为所有源地址目的地址为1.1.1.1/32[SwitchA-acl-adv-101]rule 1 permit ip source any destination 1.1.1.1 04. 将符合上述ACL规则的报文镜像到E0/8端口[SwitchA]mirrored-to ip-group 100 interface e0/8〖基于二层流的镜像〗1. 定义一个ACL[SwitchA]acl num 2002. 定义一个规则从E0/1发送至其它所有端口的数据包[SwitchA]rule 0 permit ingress interface Ethernet0/1 egress interface Ethernet0/23. 定义一个规则从其它所有端口到E0/1端口的数据包[SwitchA]rule 1 permit ingress interface Ethernet0/2 egress interface Ethernet0/14. 将符合上述ACL的数据包镜像到E0/8[SwitchA]mirrored-to link-group 200 interface e0/8
【5516/6506/6503/6506R】目前该三款产品支持对入端口流量进行镜像1. 定义镜像端口[SwitchA]monitor-port Ethernet 3/0/22. 定义被镜像端口[SwitchA]mirroring-port Ethernet 3/0/1 inbound
【补充说明】1. 镜像一般都可以实现高速率端口镜像低速率端口，例如1000M端口可以镜像100M端口，反之则无法实现2. 8016支持跨单板端口镜像端口镜像配置『环境配置参数』1. PC1接在交换机E0/1端口，IP地址1.1.1.1/242. PC2接在交换机E0/2端口，IP地址2.2.2.2/243. E0/24为交换机上行端口4. Server接在交换机E0/8端口，该端口作为镜像端口『组网需求』1. 通过交换机端口镜像的功能使用server对两台pc的业务报文进行监控。2. 按照镜像的不同方式进行配置：1) 基于端口的镜像2) 基于流的镜像2 数据配置步骤『端口镜像的数据流程』基于端口的镜像是把被镜像端口的进出数据报文完全拷贝一份到镜像端口，这样来进行流量观测或者故障定位。
【3026等交换机镜像】S2008/S2016/S2026/S2403H/S3026等交换机支持的都是基于端口的镜像，有两种方法：方法一1. 配置镜像（观测）端口[SwitchA]monitor-port e0/82. 配置被镜像端口[SwitchA]port mirror Ethernet 0/1 to Ethernet 0/2方法二1. 可以一次性定义镜像和被镜像端口[SwitchA]port mirror Ethernet 0/1 to Ethernet 0/2 observing-port Ethernet 0/8
【8016交换机端口镜像配置】1. 假设8016交换机镜像端口为E1/0/15，被镜像端口为E1/0/0，设置端口1/0/15为端口镜像的观测端口。[SwitchA] port monitor ethernet 1/0/152. 设置端口1/0/0为被镜像端口，对其输入输出数据都进行镜像。[SwitchA] port mirroring ethernet 1/0/0 both ethernet 1/0/15也可以通过两个不同的端口，对输入和输出的数据分别镜像1. 设置E1/0/15和E2/0/0为镜像（观测）端口[SwitchA] port monitor ethernet 1/0/152. 设置端口1/0/0为被镜像端口，分别使用E1/0/15和E2/0/0对输入和输出数据进行镜像。[SwitchA] port mirroring gigabitethernet 1/0/0 ingress ethernet 1/0/15[SwitchA] port mirroring gigabitethernet 1/0/0 egress ethernet 2/0/0『基于流镜像的数据流程』基于流镜像的交换机针对某些流进行镜像，每个连接都有两个方向的数据流，对于交换机来说这两个数据流是要分开镜像的。【3500/3026E/3026F/3050】〖基于三层流的镜像〗1. 定义一条扩展访问控制列表[SwitchA]acl num 1002. 定义一条规则报文源地址为1.1.1.1/32去往所有目的地址[SwitchA-acl-adv-101]rule 0 permit ip source 1.1.1.1 0 destination any3. 定义一条规则报文源地址为所有源地址目的地址为1.1.1.1/32[SwitchA-acl-adv-101]rule 1 permit ip source any destination 1.1.1.1 04. 将符合上述ACL规则的报文镜像到E0/8端口[SwitchA]mirrored-to ip-group 100 interface e0/8〖基于二层流的镜像〗1. 定义一个ACL[SwitchA]acl num 2002. 定义一个规则从E0/1发送至其它所有端口的数据包[SwitchA]rule 0 permit ingress interface Ethernet0/1 egress interface Ethernet0/23. 定义一个规则从其它所有端口到E0/1端口的数据包[SwitchA]rule 1 permit ingress interface Ethernet0/2 egress interface Ethernet0/14. 将符合上述ACL的数据包镜像到E0/8[SwitchA]mirrored-to link-group 200 interface e0/8
【5516/6506/6503/6506R】目前该三款产品支持对入端口流量进行镜像1. 定义镜像端口[SwitchA]monitor-port Ethernet 3/0/22. 定义被镜像端口[SwitchA]mirroring-port Ethernet 3/0/1 inbound
1. PC1接在交换机E0/1端口，IP地址1.1.1.1/242. PC2接在交换机E0/2端口，IP地址2.2.2.2/243. E0/24为交换机上行端口4. Server接在交换机E0/8端口，该端口作为镜像端口『组网需求』1. 通过交换机端口镜像的功能使用server对两台pc的业务报文进行监控。
2. 按照镜像的不同方式进行配置：1) 基于端口的镜像2) 基于流的镜像2 数据配置步骤『端口镜像的数据流程』基于端口的镜像是把被镜像端口的进出数据报文完全拷贝一份到镜像端口，这样来进行流量观测或者故障定位。
【3026等交换机镜像】S2008/S2016/S2026/S2403H/S3026等交换机支持的都是基于端口的镜像，有两种方法：方法一1. 配置镜像（观测）端口[SwitchA]monitor-port e0/82. 配置被镜像端口[SwitchA]port mirror Ethernet 0/1 to Ethernet 0/2方法二1. 可以一次性定义镜像和被镜像端口[SwitchA]port mirror Ethernet 0/1 to Ethernet 0/2 observing-port Ethernet 0/8
【8016交换机端口镜像配置】1. 假设8016交换机镜像端口为E1/0/15，被镜像端口为E1/0/0，设置端口1/0/15为端口镜像的观测端口。[SwitchA] port monitor ethernet 1/0/152. 设置端口1/0/0为被镜像端口，对其输入输出数据都进行镜像。[SwitchA] port mirroring ethernet 1/0/0 both ethernet 1/0/15也可以通过两个不同的端口，对输入和输出的数据分别镜像1. 设置E1/0/15和E2/0/0为镜像（观测）端口[SwitchA] port monitor ethernet 1/0/152. 设置端口1/0/0为被镜像端口，分别使用E1/0/15和E2/0/0对输入和输出数据进行镜像。[SwitchA] port mirroring gigabitethernet 1/0/0 ingress ethernet 1/0/15[SwitchA] port mirroring gigabitethernet 1/0/0 egress ethernet 2/0/0『基于流镜像的数据流程』基于流镜像的交换机针对某些流进行镜像，每个连接都有两个方向的数据流，对于交换机来说这两个数据流是要分开镜像的。【3500/3026E/3026F/3050】〖基于三层流的镜像〗1. 定义一条扩展访问控制列表[SwitchA]acl num 1002. 定义一条规则报文源地址为1.1.1.1/32去往所有目的地址[SwitchA-acl-adv-101]rule 0 permit ip source 1.1.1.1 0 destination any3. 定义一条规则报文源地址为所有源地址目的地址为1.1.1.1/32[SwitchA-acl-adv-101]rule 1 permit ip source any destination 1.1.1.1 04. 将符合上述ACL规则的报文镜像到E0/8端口[SwitchA]mirrored-to ip-group 100 interface e0/8〖基于二层流的镜像〗1. 定义一个ACL[SwitchA]acl num 2002. 定义一个规则从E0/1发送至其它所有端口的数据包[SwitchA]rule 0 permit ingress interface Ethernet0/1 egress interface Ethernet0/23. 定义一个规则从其它所有端口到E0/1端口的数据包[SwitchA]rule 1 permit ingress interface Ethernet0/2 egress interface Ethernet0/14. 将符合上述ACL的数据包镜像到E0/8[SwitchA]mirrored-to link-group 200 interface e0/8
【5516/6506/6503/6506R】目前该三款产品支持对入端口流量进行镜像1. 定义镜像端口[SwitchA]monitor-port Ethernet 3/0/22. 定义被镜像端口[SwitchA]mirroring-port Ethernet 3/0/1 inbound
【补充说明】1. 镜像一般都可以实现高速率端口镜像低速率端口，例如1000M端口可以镜像100M端口，反之则无法实现2. 8016支持跨单板端口镜像端口镜像配置『环境配置参数』1. PC1接在交换机E0/1端口，IP地址1.1.1.1/242. PC2接在交换机E0/2端口，IP地址2.2.2.2/243. E0/24为交换机上行端口4. Server接在交换机E0/8端口，该端口作为镜像端口『组网需求』1. 通过交换机端口镜像的功能使用server对两台pc的业务报文进行监控。2. 按照镜像的不同方式进行配置：1) 基于端口的镜像2) 基于流的镜像2 数据配置步骤『端口镜像的数据流程』基于端口的镜像是把被镜像端口的进出数据报文完全拷贝一份到镜像端口，这样来进行流量观测或者故障定位。
【3026等交换机镜像】S2008/S2016/S2026/S2403H/S3026等交换机支持的都是基于端口的镜像，有两种方法：方法一1. 配置镜像（观测）端口[SwitchA]monitor-port e0/82. 配置被镜像端口[SwitchA]port mirror Ethernet 0/1 to Ethernet 0/2方法二1. 可以一次性定义镜像和被镜像端口[SwitchA]port mirror Ethernet 0/1 to Ethernet 0/2 observing-port Ethernet 0/8
【8016交换机端口镜像配置】1. 假设8016交换机镜像端口为E1/0/15，被镜像端口为E1/0/0，设置端口1/0/15为端口镜像的观测端口。[SwitchA] port monitor ethernet 1/0/152. 设置端口1/0/0为被镜像端口，对其输入输出数据都进行镜像。[SwitchA] port mirroring ethernet 1/0/0 both ethernet 1/0/15也可以通过两个不同的端口，对输入和输出的数据分别镜像1. 设置E1/0/15和E2/0/0为镜像（观测）端口[SwitchA] port monitor ethernet 1/0/152. 设置端口1/0/0为被镜像端口，分别使用E1/0/15和E2/0/0对输入和输出数据进行镜像。[SwitchA] port mirroring gigabitethernet 1/0/0 ingress ethernet 1/0/15[SwitchA] port mirroring gigabitethernet 1/0/0 egress ethernet 2/0/0『基于流镜像的数据流程』基于流镜像的交换机针对某些流进行镜像，每个连接都有两个方向的数据流，对于交换机来说这两个数据流是要分开镜像的。【3500/3026E/3026F/3050】〖基于三层流的镜像〗1. 定义一条扩展访问控制列表[SwitchA]acl num 1002. 定义一条规则报文源地址为1.1.1.1/32去往所有目的地址[SwitchA-acl-adv-101]rule 0 permit ip source 1.1.1.1 0 destination any3. 定义一条规则报文源地址为所有源地址目的地址为1.1.1.1/32[SwitchA-acl-adv-101]rule 1 permit ip source any destination 1.1.1.1 04. 将符合上述ACL规则的报文镜像到E0/8端口[SwitchA]mirrored-to ip-group 100 interface e0/8〖基于二层流的镜像〗1. 定义一个ACL[SwitchA]acl num 2002. 定义一个规则从E0/1发送至其它所有端口的数据包[SwitchA]rule 0 permit ingress interface Ethernet0/1 egress interface Ethernet0/23. 定义一个规则从其它所有端口到E0/1端口的数据包[SwitchA]rule 1 permit ingress interface Ethernet0/2 egress interface Ethernet0/14. 将符合上述ACL的数据包镜像到E0/8[SwitchA]mirrored-to link-group 200 interface e0/8
【5516/6506/6503/6506R】目前该三款产品支持对入端口流量进行镜像1. 定义镜像端口[SwitchA]monitor-port Ethernet 3/0/22. 定义被镜像端口[SwitchA]mirroring-port Ethernet 3/0/1 inbound
【转帖】设计局域网几个重要因素分析
在企业现有的网络基础结构过时的时候，或者其端口速率已严重落后的时候，在企业建造新的工作环境并设计全新的局域网络的时候，都需要设计新的局域网。对一个网络工程师来说，这也许是梦寐以求的事情。但如果不正确地设计网络，这种设计有可能会成为一场噩梦。下面，就让我们看一些在设计新的局域网时需要考虑的多个关键问题。
是否要采用以太网供电(PoE)
越来越多的企业采用无线局域网技术和IP电话技术。在PoE可用时，无线局域网的接入点将容易安装。IP电话可利用连接到LAN的电话，并使用其中的电力。传统的PBX系统的日子已经很有限了;现在有大量的、越来越多的厂商都在向IP PBX系统和手持设备挻进。企业也许没有使用无线网，也许会说绝对不采用IP电话技术。但如果工程师现在能够说服企业购买PoE交换机，就应当为企业提供更好的服务。还有，在CIO决定转向WLAN或IP电话技术时，公司不必替换掉这些非PoE交换机。
需要10 Gigabit还是100 Gigabit
如今，10 Gigabit以太网及更高速度的以太网正向企业招手，但这并不意味着企业需要在所有的局域网中都采用这种高速端口。经常有这种情况，企业购买了认为真正需要的最快设备，但其原有的100Mbps网络却仅发挥了5%的性能。虽然保障核心交换机能够支持更高的速度可以真正体现出谨慎的态度，但如果工程师告诉企业说到处都需要10 Gigabit交换机，那么这就是在建议企业浪费金钱。
关于冗余性问题
网络的正常运行时间对企业来说越来越生死攸关。设计师应当计划网络设计，以便于从物理和逻辑的观点提供网络的冗余性。例如，从接线盒到核心交换机的线缆连接，可利用双光纤传输。要保障基于机架的核心交换机拥有双CPU的扩展卡。企业应当考虑一些组件，如网关的冗余性。不过，如果企业没有正确地配置组件，用来提供第三层IP缺省网关的冗余性，一旦发生故障，企业网络将陷于停顿，甚至造成不可估量的损失。
计划网络的复杂程度符合企业的IT技术
现代的交换机和路由器有大量的特性和功能。然而，如果企业的IT工作人员对工程师所实施的特性和功能并没有一个基本的理解，在网络中设计部署太多华而不实的东西在未来会产生许多支持问题。网络工程师应当在不使网络过度复杂的情况下，思考企业的实际需要。 标准和维护问题
在设计一个公司网络时，要尽力使不同种类的设备标准化，而不要在每一个接线架内使用不同类型的交换机，即使所有的设备都来自同样的制造商也是如此。对不同类型的硬件实现标准化可以简化配置和故障诊断过程。
网络管理工具问题
虽然在企业的定购单中也许不会体现出网络管理工具，但它对于提供最大的网络正常运行时间能够发挥不可估量的作用。那种能够定期地将全部设备的配置信息备份给网络共享的软件虽然简单，但却极其有用。此外，企业可以考虑下面这种情况：在企业网络上有两台交换机提供IP缺省网关的冗余性。如果其中之一发生故障，但你却并没有认识到，因为网络具有冗余性。但在另外一个交换机也失效时，企业将遭受完全的网络瘫痪。如何解决这个问题呢?企业可以通过使用一种简单的工具来ping所有的网络设备并报告其状态，从而可以轻松地避免出现这种故障。
在设计一个网络时其实有许多问题需要考虑，如终端用户设备、网络协议、应用程序、带宽、吞吐量、拓扑类型、灵活性等。本文没有讨论全部的这些因素，只是从企业的需要和发展的观点讨论了多个问题，但希望所提供的这多个方面可为企业设计网络提供正确的指导，或可作抛砖引玉之用。
是否要采用以太网供电(PoE)
越来越多的企业采用无线局域网技术和IP电话技术。在PoE可用时，无线局域网的接入点将容易安装。IP电话可利用连接到LAN的电话，并使用其中的电力。传统的PBX系统的日子已经很有限了;现在有大量的、越来越多的厂商都在向IP PBX系统和手持设备挻进。企业也许没有使用无线网，也许会说绝对不采用IP电话技术。但如果工程师现在能够说服企业购买PoE交换机，就应当为企业提供更好的服务。还有，在CIO决定转向WLAN或IP电话技术时，公司不必替换掉这些非PoE交换机。
需要10 Gigabit还是100 Gigabit
如今，10 Gigabit以太网及更高速度的以太网正向企业招手，但这并不意味着企业需要在所有的局域网中都采用这种高速端口。经常有这种情况，企业购买了认为真正需要的最快设备，但其原有的100Mbps网络却仅发挥了5%的性能。虽然保障核心交换机能够支持更高的速度可以真正体现出谨慎的态度，但如果工程师告诉企业说到处都需要10 Gigabit交换机，那么这就是在建议企业浪费金钱。
关于冗余性问题
网络的正常运行时间对企业来说越来越生死攸关。设计师应当计划网络设计，以便于从物理和逻辑的观点提供网络的冗余性。例如，从接线盒到核心交换机的线缆连接，可利用双光纤传输。要保障基于机架的核心交换机拥有双CPU的扩展卡。企业应当考虑一些组件，如网关的冗余性。不过，如果企业没有正确地配置组件，用来提供第三层IP缺省网关的冗余性，一旦发生故障，企业网络将陷于停顿，甚至造成不可估量的损失。
计划网络的复杂程度符合企业的IT技术
现代的交换机和路由器有大量的特性和功能。然而，如果企业的IT工作人员对工程师所实施的特性和功能并没有一个基本的理解，在网络中设计部署太多华而不实的东西在未来会产生许多支持问题。网络工程师应当在不使网络过度复杂的情况下，思考企业的实际需要。 标准和维护问题
在设计一个公司网络时，要尽力使不同种类的设备标准化，而不要在每一个接线架内使用不同类型的交换机，即使所有的设备都来自同样的制造商也是如此。对不同类型的硬件实现标准化可以简化配置和故障诊断过程。
网络管理工具问题
虽然在企业的定购单中也许不会体现出网络管理工具，但它对于提供最大的网络正常运行时间能够发挥不可估量的作用。那种能够定期地将全部设备的配置信息备份给网络共享的软件虽然简单，但却极其有用。此外，企业可以考虑下面这种情况：在企业网络上有两台交换机提供IP缺省网关的冗余性。如果其中之一发生故障，但你却并没有认识到，因为网络具有冗余性。但在另外一个交换机也失效时，企业将遭受完全的网络瘫痪。如何解决这个问题呢?企业可以通过使用一种简单的工具来ping所有的网络设备并报告其状态，从而可以轻松地避免出现这种故障。
在设计一个网络时其实有许多问题需要考虑，如终端用户设备、网络协议、应用程序、带宽、吞吐量、拓扑类型、灵活性等。本文没有讨论全部的这些因素，只是从企业的需要和发展的观点讨论了多个问题，但希望所提供的这多个方面可为企业设计网络提供正确的指导，或可作抛砖引玉之用。
Pass4side 路由器防火牆配置命令
Pass4side 路由器防火牆配置命令 路由器防火牆配置命令access-list 用于創建訪問規則。
（1）創建標准訪問列表access-list [ normal special ] listnumber1 { permit deny } source-addr [ source-mask ]
（2）創建擴展訪問列表access-list [ normal special ] listnumber2 { permit deny } protocol source-addr source-mask [ operator port1 [ port2 ] ] dest-addr dest-mask [ operator port1 [ port2 ] icmp-type [ icmp-code ] ] [ log ]
（3）刪除訪問列表no access-list { normal special } { all listnumber [ subitem ] }
【參數說明】normal 指定規則加入普通時間段。special 指定規則加入特殊時間段。listnumber1 是1到99之間的壹個數值，表示規則是標准訪問列表規則。listnumber2 是100到199之間的壹個數值，表示規則是擴展訪問列表規則。permit 表明允許滿足條件的報文通過。deny 表明禁止滿足條件的報文通過。protocol 爲協議類型，支持ICMP、TCP、UDP等，其它的協議也支持，此時沒有端口比較的概念；爲IP時有特殊含義，代表所有的IP協議。
source-addr 爲源地址。source-mask 爲源地址通配位，在標准訪問列表中是可選項，不輸入則代表通配位爲0.0.0.0。dest-addr 爲目的地址。dest-mask 爲目的地址通配位。operator[可選] 端口操作符，在協議類型爲TCP或UDP時支持端口比較，支持的比較操作有：等于（eq）、大于（gt）、小于（lt）、不等于（neq）或介于（range）；如果操作符爲range，則後面需要跟兩個端口。port1 在協議類型爲TCP或UDP時出現，可以爲關鍵字所設定的預設值（如telnet）或0~65535之間的壹個數值。port2 在協議類型爲TCP或UDP且操作類型爲range時出現；可以爲關鍵字所設定的預設值（如telnet）或0~65535之間的壹個數值。icmp-type[可選] 在協議爲ICMP時出現，代表ICMP報文類型；可以是關鍵字所設定的預設值（如echo-reply）或者是0~255之間的壹個數值。icmp-code在協議爲ICMP且沒有選擇所設定的預設值時出現；代表ICMP碼，是0~255之間的壹個數值。log [可選] 表示如果報文符合條件，需要做日志。listnumber 爲刪除的規則序號，是1~199之間的壹個數值。subitem[可選] 指定刪除序號爲listnumber的訪問列表中規則的序號。
【缺省情況】 系統缺省不配置任何訪問規則。
【命令模式】 全局配置模式
【使用指南】同壹個序號的規則可以看作壹類規則；所定義的規則不僅可以用來在接口上過濾報文，也可以被如DDR等用來判斷壹個報文是否是感興趣的報文，此時，permit與deny表示是感興趣的還是不感興趣的。使用協議域爲IP的擴展訪問列表來表示所有的IP協議。同壹個序號之間的規則按照壹定的原則進行排列和選擇，這個順序可以通過 show access-list 命令看到。
【舉例】允許源地址爲10.1.1.0 網絡、目的地址爲10.1.2.0網絡的WWW訪問，但不允許使用FTP。Quidway(config)#access-list 100 permit tcp 10.1.1.0 0.0.0.255 10.1.2.0 0.0.0.255 eq wwwQuidway(config)#access-list 100 deny tcp 10.1.1.0 0.0.0.255 10.1.2.0 0.0.0.255 eq ftp
【相關命令】ip access-group二、clear access-list counters 清除訪問列表規則的統計信息。clear access-list counters [ listnumber ]
【參數說明】listnumber [可選] 要清除統計信息的規則的序號，如不指定，則清除所有的規則的統計信息。
【缺省情況】 任何時候都不清除統計信息。
【命令模式】 特權用戶模式
【使用指南】使用此命令來清除當前所用規則的統計信息，不指定規則編號則清除所有規則的統計信息。
【舉例】例1：清除當前所使用的序號爲100的規則的統計信息。Quidway#clear access-list counters 100例2：清除當前所使用的所有規則的統計信息。Quidway#clear access-list counters【相關命令】access-list三、firewall 啓用或禁止防火牆。firewall { enable disable }
【參數說明】 enable 表示啓用防火牆。 disable 表示禁止防火牆。
【缺省情況】 系統缺省爲禁止防火牆。
【命令模式】 全局配置模式
【使用指南】使用此命令來啓用或禁止防火牆，可以通過show firewall命令看到相應結果。如果采用了時間段包過濾，則在防火牆被關閉時也將被關閉；該命令控制防火牆的總開關。在使用 firewall disable 命令關閉防火牆時，防火牆本身的統計信息也將被清除。
【舉例】 啓用防火牆。Quidway(config)#firewall enable
【相關命令】access-list，ip access-group四、firewall default 配置防火牆在沒有相應的訪問規則匹配時，缺省的過濾方式。firewall default { permit deny }
【參數說明】permit 表示缺省過濾屬性設置爲“允許”。deny 表示缺省過濾屬性設置爲“禁止”。
【缺省情況】在防火牆開啓的情況下，報文被缺省允許通過。
【命令模式】 全局配置模式
【使用指南】當在接口應用的規則沒有壹個能夠判斷壹個報文是否應該被允許還是禁止時，缺省的過濾屬性將起作用；如果缺省過濾屬性是“允許”，則報文可以通過，否則報文被丟棄。
【舉例】 設置缺省過濾屬性爲“允許”。Quidway(config)#firewall default permit五、ip access-group 使用此命令將規則應用到接口上。使用此命令的no形式來刪除相應的設置。ip access-group listnumber { in out }[ no ] ip access-group listnumber { in out }
【參數說明】listnumber 爲規則序號，是1~199之間的壹個數值。in 表示規則用于過濾從接口收上來的報文。out 表示規則用于過濾從接口轉發的報文。
【缺省情況】 沒有規則應用于接口。
【命令模式】 接口配置模式。
【使用指南】使用此命令來將規則應用到接口上；如果要過濾從接口收上來的報文，則使用 in 關鍵字；如果要過濾從接口轉發的報文，使用out 關鍵字。壹個接口的壹個方向上最多可以應用20類不同的規則；這些規則之間按照規則序號的大小進行排列，序號大的排在前面，也就是優先級高。對報文進行過濾時，將采用發現符合的規則即得出過濾結果的方法來加快過濾速度。所以，建議在配置規則時，盡量將對同壹個網絡配置的規則放在同壹個序號的訪問列表中；在同壹個序號的訪問列表中，規則之間的排列和選擇順序可以用show access-list命令來查看。
【舉例】將規則101應用于過濾從以太網口收上來的報文。Quidway(config-if-Ethernet0)#ip access-group 101 in
【相關命令】 access-list六、settr 設定或取消特殊時間段。settr begin-time end-timeno settr【參數說明】 begin-time 爲壹個時間段的開始時間。end-time 爲壹個時間段的結束時間，應該大于開始時間。
【缺省情況】 系統缺省沒有設置時間段，即認爲全部爲普通時間段。
【命令模式】 全局配置模式
【使用指南】使用此命令來設置時間段；可以最多同時設置6個時間段，通過show timerange 命令可以看到所設置的時間。如果在已經使用了壹個時間段的情況下改變時間段，則此修改將在壹分鍾左右生效（系統查詢時間段的時間間隔）。設置的時間應該是24小時制。如果要設置類似晚上9點到早上8點的時間段，可以設置成“settr 21:00 23:59 0:00 8:00”，因爲所設置的時間段的兩個端點屬于時間段之內，故不會産生時間段內外的切換。另外這個設置也經過了2000問題的測試。
【舉例】例1：設置時間段爲8:30 ~ 12:00，14:00 ~ 17:00。Quidway(config)#settr 8:30 12:00 14:00 17:00例2： 設置時間段爲晚上9點到早上8點。Quidway(config)#settr 21:00 23:59 0:00 8:0
【相關命令】 timerange，show timerange七、show access-list 顯示包過濾規則及在接口上的應用。show access-list [ all listnumber interface interface-name ]
【參數說明】all 表示所有的規則，包括普通時間段內及特殊時間段內的規則。listnumber 爲顯示當前所使用的規則中序號爲listnumber的規則。interface 表示要顯示在指定接口上應用的規則序號。interface-name 爲接口的名稱。
【命令模式】 特權用戶模式
【使用指南】使用此命令來顯示所指定的規則，同時查看規則過濾報文的情況。每個規則都有壹個相應的計數器，如果用此規則過濾了壹個報文，則計數器加1；通過對計數器的觀察可以看出所配置的規則中，哪些規則是比較有效，而哪些基本無效。可以通過帶interface關鍵字的show access-list命令來查看某個接口應用規則的情況。
【舉例】例1：顯示當前所使用的序號爲100的規則。Quidway#show access-list 100Using normal packet-filtering access rules now.100 deny icmp 10.1.0.0 0.0.255.255 any host-redirect (3 matches,252 bytes — rule 1)100 permit icmp 10.1.0.0 0.0.255.255 any echo (no matches — rule 2)100 deny udp any any eq rip (no matches — rule 3)例2： 顯示接口Serial0上應用規則的情況。Quidway#show access-list interface serial 0Serial0:access-list filtering In-bound packets : 120access-list filtering Out-bound packets: None
【相關命令】 access-list八、show firewall 顯示防火牆狀態。show firewall
【命令模式】 特權用戶模式
【使用指南】使用此命令來顯示防火牆的狀態，包括防火牆是否被啓用，啓用防火牆時是否采用了時間段包過濾及防火牆的壹些統計信息。
【舉例】顯示防火牆狀態。Quidway#show firewallFirewall is enable, default filtering method is ‘permit’.TimeRange packet-filtering enable.InBound packets: None;OutBound packets: 0 packets, 0 bytes, 0% permitted,0 packets, 0 bytes, 0% denied,2 packets, 104 bytes, 100% permitted defaultly,0 packets, 0 bytes, 100% denied defaultly.From 00:13:02 to 06:13:21: 0 packets, 0 bytes, permitted.
【相關命令】 firewall九、show isintr 顯示當前時間是否在時間段之內。show isintr
【命令模式】 特權用戶模式
【使用指南】使用此命令來顯示當前時間是否在時間段之內。
【舉例】 顯示當前時間是否在時間段之內。Quidway#show isintrIt is NOT in time ranges now.【相關命令】 timerange，settr十、show timerange 顯示時間段包過濾的信息。show timerange
【命令模式】 特權用戶模式
【使用指南】 使用此命令來顯示當前是否允許時間段包過濾及所設置的時間段。
【舉例】 顯示時間段包過濾的信息。Quidway#show timerangeTimeRange packet-filtering enable.beginning of time range:01:00 - 02:0003:00 - 04:00end of time range.
【相關命令】 timerange，settr十壹、timerange 啓用或禁止時間段包過濾功能。timerange { enable disable }
【參數說明】 enable 表示啓用時間段包過濾。disable 表示禁止采用時間段包過濾。【缺省情況】 系統缺省爲禁止時間段包過濾功能。
【命令模式】 全局配置模式
【使用指南】使用此命令來啓用或禁止時間段包過濾功能，可以通過show firewall命令看到，也可以通過show timerange命令看到配置結果。在時間段包過濾功能被啓用後，系統將根據當前的時間和設置的時間段來確定使用時間段內（特殊）的規則還是時間段外（普通）的規則。系統查詢時間段的精確度爲1分鍾。所設置的時間段的兩個端點屬于時間段之內。
【舉例】 啓用時間段包過濾功能。Quidway(config)#timerange enable
【相關命令】 settr，show timerange
（1）創建標准訪問列表access-list [ normal special ] listnumber1 { permit deny } source-addr [ source-mask ]
（2）創建擴展訪問列表access-list [ normal special ] listnumber2 { permit deny } protocol source-addr source-mask [ operator port1 [ port2 ] ] dest-addr dest-mask [ operator port1 [ port2 ] icmp-type [ icmp-code ] ] [ log ]
（3）刪除訪問列表no access-list { normal special } { all listnumber [ subitem ] }
【參數說明】normal 指定規則加入普通時間段。special 指定規則加入特殊時間段。listnumber1 是1到99之間的壹個數值，表示規則是標准訪問列表規則。listnumber2 是100到199之間的壹個數值，表示規則是擴展訪問列表規則。permit 表明允許滿足條件的報文通過。deny 表明禁止滿足條件的報文通過。protocol 爲協議類型，支持ICMP、TCP、UDP等，其它的協議也支持，此時沒有端口比較的概念；爲IP時有特殊含義，代表所有的IP協議。
source-addr 爲源地址。source-mask 爲源地址通配位，在標准訪問列表中是可選項，不輸入則代表通配位爲0.0.0.0。dest-addr 爲目的地址。dest-mask 爲目的地址通配位。operator[可選] 端口操作符，在協議類型爲TCP或UDP時支持端口比較，支持的比較操作有：等于（eq）、大于（gt）、小于（lt）、不等于（neq）或介于（range）；如果操作符爲range，則後面需要跟兩個端口。port1 在協議類型爲TCP或UDP時出現，可以爲關鍵字所設定的預設值（如telnet）或0~65535之間的壹個數值。port2 在協議類型爲TCP或UDP且操作類型爲range時出現；可以爲關鍵字所設定的預設值（如telnet）或0~65535之間的壹個數值。icmp-type[可選] 在協議爲ICMP時出現，代表ICMP報文類型；可以是關鍵字所設定的預設值（如echo-reply）或者是0~255之間的壹個數值。icmp-code在協議爲ICMP且沒有選擇所設定的預設值時出現；代表ICMP碼，是0~255之間的壹個數值。log [可選] 表示如果報文符合條件，需要做日志。listnumber 爲刪除的規則序號，是1~199之間的壹個數值。subitem[可選] 指定刪除序號爲listnumber的訪問列表中規則的序號。
【缺省情況】 系統缺省不配置任何訪問規則。
【命令模式】 全局配置模式
【使用指南】同壹個序號的規則可以看作壹類規則；所定義的規則不僅可以用來在接口上過濾報文，也可以被如DDR等用來判斷壹個報文是否是感興趣的報文，此時，permit與deny表示是感興趣的還是不感興趣的。使用協議域爲IP的擴展訪問列表來表示所有的IP協議。同壹個序號之間的規則按照壹定的原則進行排列和選擇，這個順序可以通過 show access-list 命令看到。
【舉例】允許源地址爲10.1.1.0 網絡、目的地址爲10.1.2.0網絡的WWW訪問，但不允許使用FTP。Quidway(config)#access-list 100 permit tcp 10.1.1.0 0.0.0.255 10.1.2.0 0.0.0.255 eq wwwQuidway(config)#access-list 100 deny tcp 10.1.1.0 0.0.0.255 10.1.2.0 0.0.0.255 eq ftp
【相關命令】ip access-group二、clear access-list counters 清除訪問列表規則的統計信息。clear access-list counters [ listnumber ]
【參數說明】listnumber [可選] 要清除統計信息的規則的序號，如不指定，則清除所有的規則的統計信息。
【缺省情況】 任何時候都不清除統計信息。
【命令模式】 特權用戶模式
【使用指南】使用此命令來清除當前所用規則的統計信息，不指定規則編號則清除所有規則的統計信息。
【舉例】例1：清除當前所使用的序號爲100的規則的統計信息。Quidway#clear access-list counters 100例2：清除當前所使用的所有規則的統計信息。Quidway#clear access-list counters【相關命令】access-list三、firewall 啓用或禁止防火牆。firewall { enable disable }
【參數說明】 enable 表示啓用防火牆。 disable 表示禁止防火牆。
【缺省情況】 系統缺省爲禁止防火牆。
【命令模式】 全局配置模式
【使用指南】使用此命令來啓用或禁止防火牆，可以通過show firewall命令看到相應結果。如果采用了時間段包過濾，則在防火牆被關閉時也將被關閉；該命令控制防火牆的總開關。在使用 firewall disable 命令關閉防火牆時，防火牆本身的統計信息也將被清除。
【舉例】 啓用防火牆。Quidway(config)#firewall enable
【相關命令】access-list，ip access-group四、firewall default 配置防火牆在沒有相應的訪問規則匹配時，缺省的過濾方式。firewall default { permit deny }
【參數說明】permit 表示缺省過濾屬性設置爲“允許”。deny 表示缺省過濾屬性設置爲“禁止”。
【缺省情況】在防火牆開啓的情況下，報文被缺省允許通過。
【命令模式】 全局配置模式
【使用指南】當在接口應用的規則沒有壹個能夠判斷壹個報文是否應該被允許還是禁止時，缺省的過濾屬性將起作用；如果缺省過濾屬性是“允許”，則報文可以通過，否則報文被丟棄。
【舉例】 設置缺省過濾屬性爲“允許”。Quidway(config)#firewall default permit五、ip access-group 使用此命令將規則應用到接口上。使用此命令的no形式來刪除相應的設置。ip access-group listnumber { in out }[ no ] ip access-group listnumber { in out }
【參數說明】listnumber 爲規則序號，是1~199之間的壹個數值。in 表示規則用于過濾從接口收上來的報文。out 表示規則用于過濾從接口轉發的報文。
【缺省情況】 沒有規則應用于接口。
【命令模式】 接口配置模式。
【使用指南】使用此命令來將規則應用到接口上；如果要過濾從接口收上來的報文，則使用 in 關鍵字；如果要過濾從接口轉發的報文，使用out 關鍵字。壹個接口的壹個方向上最多可以應用20類不同的規則；這些規則之間按照規則序號的大小進行排列，序號大的排在前面，也就是優先級高。對報文進行過濾時，將采用發現符合的規則即得出過濾結果的方法來加快過濾速度。所以，建議在配置規則時，盡量將對同壹個網絡配置的規則放在同壹個序號的訪問列表中；在同壹個序號的訪問列表中，規則之間的排列和選擇順序可以用show access-list命令來查看。
【舉例】將規則101應用于過濾從以太網口收上來的報文。Quidway(config-if-Ethernet0)#ip access-group 101 in
【相關命令】 access-list六、settr 設定或取消特殊時間段。settr begin-time end-timeno settr【參數說明】 begin-time 爲壹個時間段的開始時間。end-time 爲壹個時間段的結束時間，應該大于開始時間。
【缺省情況】 系統缺省沒有設置時間段，即認爲全部爲普通時間段。
【命令模式】 全局配置模式
【使用指南】使用此命令來設置時間段；可以最多同時設置6個時間段，通過show timerange 命令可以看到所設置的時間。如果在已經使用了壹個時間段的情況下改變時間段，則此修改將在壹分鍾左右生效（系統查詢時間段的時間間隔）。設置的時間應該是24小時制。如果要設置類似晚上9點到早上8點的時間段，可以設置成“settr 21:00 23:59 0:00 8:00”，因爲所設置的時間段的兩個端點屬于時間段之內，故不會産生時間段內外的切換。另外這個設置也經過了2000問題的測試。
【舉例】例1：設置時間段爲8:30 ~ 12:00，14:00 ~ 17:00。Quidway(config)#settr 8:30 12:00 14:00 17:00例2： 設置時間段爲晚上9點到早上8點。Quidway(config)#settr 21:00 23:59 0:00 8:0
【相關命令】 timerange，show timerange七、show access-list 顯示包過濾規則及在接口上的應用。show access-list [ all listnumber interface interface-name ]
【參數說明】all 表示所有的規則，包括普通時間段內及特殊時間段內的規則。listnumber 爲顯示當前所使用的規則中序號爲listnumber的規則。interface 表示要顯示在指定接口上應用的規則序號。interface-name 爲接口的名稱。
【命令模式】 特權用戶模式
【使用指南】使用此命令來顯示所指定的規則，同時查看規則過濾報文的情況。每個規則都有壹個相應的計數器，如果用此規則過濾了壹個報文，則計數器加1；通過對計數器的觀察可以看出所配置的規則中，哪些規則是比較有效，而哪些基本無效。可以通過帶interface關鍵字的show access-list命令來查看某個接口應用規則的情況。
【舉例】例1：顯示當前所使用的序號爲100的規則。Quidway#show access-list 100Using normal packet-filtering access rules now.100 deny icmp 10.1.0.0 0.0.255.255 any host-redirect (3 matches,252 bytes — rule 1)100 permit icmp 10.1.0.0 0.0.255.255 any echo (no matches — rule 2)100 deny udp any any eq rip (no matches — rule 3)例2： 顯示接口Serial0上應用規則的情況。Quidway#show access-list interface serial 0Serial0:access-list filtering In-bound packets : 120access-list filtering Out-bound packets: None
【相關命令】 access-list八、show firewall 顯示防火牆狀態。show firewall
【命令模式】 特權用戶模式
【使用指南】使用此命令來顯示防火牆的狀態，包括防火牆是否被啓用，啓用防火牆時是否采用了時間段包過濾及防火牆的壹些統計信息。
【舉例】顯示防火牆狀態。Quidway#show firewallFirewall is enable, default filtering method is ‘permit’.TimeRange packet-filtering enable.InBound packets: None;OutBound packets: 0 packets, 0 bytes, 0% permitted,0 packets, 0 bytes, 0% denied,2 packets, 104 bytes, 100% permitted defaultly,0 packets, 0 bytes, 100% denied defaultly.From 00:13:02 to 06:13:21: 0 packets, 0 bytes, permitted.
【相關命令】 firewall九、show isintr 顯示當前時間是否在時間段之內。show isintr
【命令模式】 特權用戶模式
【使用指南】使用此命令來顯示當前時間是否在時間段之內。
【舉例】 顯示當前時間是否在時間段之內。Quidway#show isintrIt is NOT in time ranges now.【相關命令】 timerange，settr十、show timerange 顯示時間段包過濾的信息。show timerange
【命令模式】 特權用戶模式
【使用指南】 使用此命令來顯示當前是否允許時間段包過濾及所設置的時間段。
【舉例】 顯示時間段包過濾的信息。Quidway#show timerangeTimeRange packet-filtering enable.beginning of time range:01:00 - 02:0003:00 - 04:00end of time range.
【相關命令】 timerange，settr十壹、timerange 啓用或禁止時間段包過濾功能。timerange { enable disable }
【參數說明】 enable 表示啓用時間段包過濾。disable 表示禁止采用時間段包過濾。【缺省情況】 系統缺省爲禁止時間段包過濾功能。
【命令模式】 全局配置模式
【使用指南】使用此命令來啓用或禁止時間段包過濾功能，可以通過show firewall命令看到，也可以通過show timerange命令看到配置結果。在時間段包過濾功能被啓用後，系統將根據當前的時間和設置的時間段來確定使用時間段內（特殊）的規則還是時間段外（普通）的規則。系統查詢時間段的精確度爲1分鍾。所設置的時間段的兩個端點屬于時間段之內。
【舉例】 啓用時間段包過濾功能。Quidway(config)#timerange enable
【相關命令】 settr，show timerange
Pass4side 交换机的基础知识
许多新型的Client／Server应用程序以及多媒体技术的出现，导致了传统 的共享式网络远远不能满足要求，这也就推动了局域网交换机的出现。
1、交换机的定义 局域网交换机拥有许多端口，每个端口有自己的专用带宽，并且可以连接不同的网段。交换机各个端口之间的通信是同时的、并行的，这就大大提高了信息吞吐量。为了进一步提高性能，每个端口还可以只连接一个设备。为了实现交换机之间的互连或与高档服务器的连接，局域网交换机一般拥有一个或几个高速端口，如100M以太网端口、FDDI端口或155M ATM端口，从而保证整个网络的传输性能。
2、交换机的特性 通过集线器共享局域网的用户不仅是共享带宽，而且是竞争带宽。可能由于个别用户需要更多的带宽而导致其他用户的可用带宽相对减少，甚至被迫等待，因而也就耽误了通信和信息处理。利用交换机的网络微分段技术，可以将一个大型的共享式局域网的用户分成许多独立的网段，减少竞争带宽的用户数量，增加每个用户的可用带宽，从而缓解共享网络的拥挤状况。由于交换机可以将信息迅速而直接地送到目的地能大大提高速度和带宽，能 保护用户以前在介质方面的投资，并提供良好的可扩展性，因此交换机不但是网桥的理想替代物，而且是集线器的理想替代物。与网桥和集线器相比，交换机从下面几方面改进了性能：
（1）通过支持并行通信，提高了交换机的信息吞吐量。
（2）将传统的一个大局域网上的用户分成若干工作组，每个端口连接一台设备 或连接一个工作组，有效地解决拥挤现像。这种方法人们称之为网络微分 段（Micro一segmentation）技术。（3）虚拟网（VirtuaI LAN）技术的出现，给交换机的使用和管理带来了更大 的灵活性。我们将在后面专门介绍虚拟网。
（4）端口密度可以与集线器相媲美,一般的网络系统都是有一个或几个服务器，而绝大部分都是普通的客户机。客户机都需要访问服务器，这样就导致服务器的通信和事务处理能力成为整个网络性能好坏的关键。交换机就主要从提高连接服务器的端口的速率以及相应的帧缓冲区的大小，来提高整个网络的性能，从而满足用户的要求。一些高档的交换机还采用全双工技术进一步提高端口的带宽。以前的网络设备基本上都是采用半双工的工作方式，即当一台主机发送数据包的时候， 它就不能接收数据包，当接收数据包的时候，就不能发送数据包。由于采用全双工技术，即主机在发送数据包的同时，还可以接收数据包，普通的10M端口就可以变成20M端口，普通的100M端口就可以变成200M 端口，这样就进一步提高了信息吞吐量。
3、交换机的工作原理传统的交换机本质上是具有流量控制能力的多端口网桥，即传统的（二层） 交换机。
把路由技术引入交换机，可以完成网络层路由选择，故称为三层交换，这是交换机的新进展。交换机（二层交换）的工作原理交换机和网桥一样，是工作在链路层的联网设备，它的各个端口都具有桥接功能，每个端口可以连接一个LAN或一台高性能网站或服务器，能够通过自学习来了解每个端口的设备连接情况。所有端口由专用处理器进行控制，并经过控制管理总线转发信息。同时可以用专门的网管软件进行集中管理。 除此之外，交换机为了提高数据交换的速度和效率，一般支持多种方式。
（1）存储转发：所有常规网桥都使用这种方法。它们在将数据帧发柱其他端口之前，要把收到的帧完全存储在内部的存储器中，对其检验后再发往其他端口，这样其延时等于接收一个完整的数据帧的时间及处理时间的总和。如果级联很长时，会导致严重的性能问题，但这种方法可以过滤掉错误的数据帧。
（2）切入法：这种方法只检验数据帧的目标地址，这使得数据帧几乎马上就 可以传出去，从而大大降低延时。其缺点是：错误帧也会被传出去。错误帧的概率较小的情况下，可以采用切入法以提高传输速度。而错误帧的概率较大的情况下，可以采用存储转发法／以减少错误帧的重传。4、交换机的配置我们下面以Cisco公司的Catlystl900交换机为例，介绍交换机的一般配置过程。对一台新的Catlystl900交换机，使用它的缺省配置就可以工作了。这因为它是一种将软件装在FlashMemory中的硬件设备，当加电时，它首先要进行一系列自检，对所有端口进行测试之后，交换机就处于工作状态。这时它的交换表是空的，它可以通过自学习来了解各个端口的设备连接情况，并将设备的 MAC地址记录在交换表中，当有信息交换时，交换机就根据交换表来进行数据转发。但为了便于对它进行网络管理，Catlystl900交换机自己有一个MAC地址，这样就可以为它分配一个IP地址和屏蔽码。网络管理员须通过交换机的串口接一台终端或仿真终端，才能为它指定一个IP地址，其缺省值是0．0．0．0。指定IP地址以后，网络管理员就可以通过网络进行远程管理了。
Catlystl900交换机的配置界面是菜单形式，缺省配置下，它的所有端口都属于同一个VLAN，很多情况下都不需要作什么修改
1、交换机的定义 局域网交换机拥有许多端口，每个端口有自己的专用带宽，并且可以连接不同的网段。交换机各个端口之间的通信是同时的、并行的，这就大大提高了信息吞吐量。为了进一步提高性能，每个端口还可以只连接一个设备。为了实现交换机之间的互连或与高档服务器的连接，局域网交换机一般拥有一个或几个高速端口，如100M以太网端口、FDDI端口或155M ATM端口，从而保证整个网络的传输性能。
2、交换机的特性 通过集线器共享局域网的用户不仅是共享带宽，而且是竞争带宽。可能由于个别用户需要更多的带宽而导致其他用户的可用带宽相对减少，甚至被迫等待，因而也就耽误了通信和信息处理。利用交换机的网络微分段技术，可以将一个大型的共享式局域网的用户分成许多独立的网段，减少竞争带宽的用户数量，增加每个用户的可用带宽，从而缓解共享网络的拥挤状况。由于交换机可以将信息迅速而直接地送到目的地能大大提高速度和带宽，能 保护用户以前在介质方面的投资，并提供良好的可扩展性，因此交换机不但是网桥的理想替代物，而且是集线器的理想替代物。与网桥和集线器相比，交换机从下面几方面改进了性能：
（1）通过支持并行通信，提高了交换机的信息吞吐量。
（2）将传统的一个大局域网上的用户分成若干工作组，每个端口连接一台设备 或连接一个工作组，有效地解决拥挤现像。这种方法人们称之为网络微分 段（Micro一segmentation）技术。（3）虚拟网（VirtuaI LAN）技术的出现，给交换机的使用和管理带来了更大 的灵活性。我们将在后面专门介绍虚拟网。
（4）端口密度可以与集线器相媲美,一般的网络系统都是有一个或几个服务器，而绝大部分都是普通的客户机。客户机都需要访问服务器，这样就导致服务器的通信和事务处理能力成为整个网络性能好坏的关键。交换机就主要从提高连接服务器的端口的速率以及相应的帧缓冲区的大小，来提高整个网络的性能，从而满足用户的要求。一些高档的交换机还采用全双工技术进一步提高端口的带宽。以前的网络设备基本上都是采用半双工的工作方式，即当一台主机发送数据包的时候， 它就不能接收数据包，当接收数据包的时候，就不能发送数据包。由于采用全双工技术，即主机在发送数据包的同时，还可以接收数据包，普通的10M端口就可以变成20M端口，普通的100M端口就可以变成200M 端口，这样就进一步提高了信息吞吐量。
3、交换机的工作原理传统的交换机本质上是具有流量控制能力的多端口网桥，即传统的（二层） 交换机。
把路由技术引入交换机，可以完成网络层路由选择，故称为三层交换，这是交换机的新进展。交换机（二层交换）的工作原理交换机和网桥一样，是工作在链路层的联网设备，它的各个端口都具有桥接功能，每个端口可以连接一个LAN或一台高性能网站或服务器，能够通过自学习来了解每个端口的设备连接情况。所有端口由专用处理器进行控制，并经过控制管理总线转发信息。同时可以用专门的网管软件进行集中管理。 除此之外，交换机为了提高数据交换的速度和效率，一般支持多种方式。
（1）存储转发：所有常规网桥都使用这种方法。它们在将数据帧发柱其他端口之前，要把收到的帧完全存储在内部的存储器中，对其检验后再发往其他端口，这样其延时等于接收一个完整的数据帧的时间及处理时间的总和。如果级联很长时，会导致严重的性能问题，但这种方法可以过滤掉错误的数据帧。
（2）切入法：这种方法只检验数据帧的目标地址，这使得数据帧几乎马上就 可以传出去，从而大大降低延时。其缺点是：错误帧也会被传出去。错误帧的概率较小的情况下，可以采用切入法以提高传输速度。而错误帧的概率较大的情况下，可以采用存储转发法／以减少错误帧的重传。4、交换机的配置我们下面以Cisco公司的Catlystl900交换机为例，介绍交换机的一般配置过程。对一台新的Catlystl900交换机，使用它的缺省配置就可以工作了。这因为它是一种将软件装在FlashMemory中的硬件设备，当加电时，它首先要进行一系列自检，对所有端口进行测试之后，交换机就处于工作状态。这时它的交换表是空的，它可以通过自学习来了解各个端口的设备连接情况，并将设备的 MAC地址记录在交换表中，当有信息交换时，交换机就根据交换表来进行数据转发。但为了便于对它进行网络管理，Catlystl900交换机自己有一个MAC地址，这样就可以为它分配一个IP地址和屏蔽码。网络管理员须通过交换机的串口接一台终端或仿真终端，才能为它指定一个IP地址，其缺省值是0．0．0．0。指定IP地址以后，网络管理员就可以通过网络进行远程管理了。
Catlystl900交换机的配置界面是菜单形式，缺省配置下，它的所有端口都属于同一个VLAN，很多情况下都不需要作什么修改
2008年9月15日星期一
Pass4side SUN 310-052考试题库分享（1-5）
1. What are the three primary roles in a web service interaction? (Choose three.)A. BrokerB. FacadeC. ProviderD. DecoratorE. RequestorF. InterceptorAnswer: ACE更多最新考试信息可登陆http://www.pass4side.cn/网站查看！本文考试题库摘自pass4side.cn 更新时间：2008-9-112. A stock trading company is writing a new application for stock market forecasting. A significant portion of thework required by the business logic involves navigating through the persistent object model. As lead architect onthis project, you have chosen JPA over EJB2 entity beans to implement these persistent objects. You have donethis to maximize performance when navigating through the model. Why does JPA offer better performance for thistask?A. JPA guarantees referential integrity at the object level.B. JPA allows the application to specify lazy or eager retrievals.C. JPA simplifies the source code that implements the object model.D. The guaranteed referential integrity in EJB2 entity beans is expensive.Answer: B
3. A developer creates a Java web service to be used by consumers in an SOA. This SOA uses a UDDI serviceregistry. How can the developer make the new service available to consumers?A. deploy to the registry using JAXRB. publish to the registry using JAXRC. query the registry using JAX-RPCD. target the registry using JAX-RPCAnswer: B
4. With the release of a new product line, there has been a significant increase in the volume of transactions onyour web site. You need to scale your application and manage session failover. What is the best option forscalability?A. add additional web servers and application serversB. introduce a High Availability pair and utilize sticky sessionsC. add additional application servers and implement DNS round robinD. add additional application servers and use clustered HttpSessionAnswer: D
5. You are asked to architect an SOA solution that leverages Java web services. The architecture needs to beflexible and allow for the SOAP 1.1, SOAP 1.2, and REST implementations. Which Java EE technology shouldyou use?A. JAXPB. JAXBC. JAX-WSD. JAX-RPCAnswer: C
更多最新考试信息可登陆http://www.pass4side.cn/网站查看！本文考试题库摘自pass4side.cn 更新时间：2008-9-11
2008年9月11日星期四
Pass4side Comptia A+ Certification Faq
We get the same questions,and give the same answers, so often I wanted to group all the answers together on one page. Let me know if you cne up with more.A+ is a two part test Hardware or core(220-301) Operating System (220-302)900 is perfect score, 515 passes hardware, 505 passes OS80 questions for each test. (no more adaptive test)90 minutes for each test.No, you do not have to take both test on the same day.Yes, you could if you wanted to.No time limit between tests.Yes, you can mark questions for review and go back if you have time.No, you can’t take notes, books, cell phone, pda, etc. in the testing room.They provide pencil and paper to make your own notes.Yes, you get a printout with your pass/fail grade before you leave.No waiting to retake after first fail, 30 days after 2nd failYes, there is a separate charge for each test.You can find testing sites at CompTIA web site : http://www.pass4side.cn Phone number is under customer support, contact us)No word on CompTIA changing the A+ test.No announcement of test change.No updated books yet.Still using 2003 test objectives.Yes, 2003 A+ books are still good.One day the test will change. When we know, you will know. Please check forum for an update (stop worrying).Get the idea?..no change yetNo two tests are the same. CompTIA has thousands of questions to pick from.That?s why brain dumps DON’T work.
BSCI 642-901 Exam
ccnp认证，是获得新的面貌于2007年底。该bsci和bcmsn考试，正在更新，以及创新科技委员会和bcran考试，现正退休。用户年龄？有何考虑一下有什么期望新bsci考试。 据ciscoa ？有何考试的蓝图-无可否认，一个很广泛的蓝图，在这个时候-新的重大课题的I P版本6（ I P v6）和多播。加上这两个议题，将使已经要求思科认证考试，有很多强硬的，但是这是一个伟大的变化，为考试，并为候选人的资格。 IPv6是刚才去becne越来越多的流行在todaya ？有何网络，和多播是一样。 多播为思科ccnp bsci考试是要远远超出你了解了它在您的ccna研究。为新bsci考试， youa吗？当地雇员需要知道不同的方法，建立多播组，以及分配给他们的成员。这种材料以前仅限于ccie级别的书籍，虽然我多纳吗？吨查找问题，要努力为ccie笔试，组播并不是一件容易的题目，不应该掉以轻心，由ccnp候选人在2007年。 一个主要的ccnp考试题目isna吗？吨，是去任何地方的骨钙素。该边界网关协议已被一个大的一部分，以前的bsci考试，并期待继续下去。 如果youa吗？重新追求你的ccnp认证在2008年，一定要监察ciscoa吗？网站为补充，向ccnp的蓝图。 ITA成员？有何很明显，思科提出了进入该市场的门槛ccnp认证，入这个重要的思科认证将反过来又提高您的市场价值和网络知识一样，以前从未。观赏为今后的教学研究其他三个新的ccnp考试！ 克里斯科比， ccie ＃ 12933 ，是业主的科比优势，家中超过100个免费的认证考试指南，包括思科ccna认证测试准备的文章。他的专访思科ccna学习指南和思科ccna培训，也可！ 思科ccnp认证考试 642-812, 642-825, 642-845, 642-892, 642-901, 642-801, 642-821, 642-831. Fromhttp://www.pass4side.cn/
Pass4side Cognos 8 BI Modeler BI0-130 权威考题
Pass4side Cognos 8 BI Modeler BI0-130 权威考题BI0-130考试是COGNOS公司的官方认证考试代号，Pass4Side的BI0-130权威考试题库软件是COGNOS认证厂商的授权产品考题数量: 105:Q&As更新时间: 2008-8-30
免费DEMO下载地址：http://download.pass4side.com/BI0-130.zip
免费DEMO下载地址：http://download.pass4side.com/BI0-130.zip
Pass4side Huawei H3C Certified Network Engineer GB0-180 权威考题
Pass4side Huawei H3C Certified Network Engineer GB0-180 权威考题GB0-180考试是H3C公司的官方认证考试代号，Pass4Side的GB0-180权威考试题库软件是H3C认证厂商的授权产品考题数量: 400:Q&As更新时间: 2008-6-1DEMO免费下载地址：http://download.pass4side.com/GB0-180.zip
Huawei Designing Enterprise-level Networks Pass4side GB0-360
Huawei Designing Enterprise-level Networks Pass4side GB0-360GB0-360考试是H3C公司的官方认证考试代号，Pass4Side的GB0-360权威考试题库软件是H3C认证厂商的授权产品考题数量: 400:Q&As更新时间: 2008-6-12DEMO免费下载地址：http://download.pass4side.com/GB0-360.zip
H3C Constructing Enterprise-level Switching Networks Pass4side GB0-320
H3C Constructing Enterprise-level Switching Networks Pass4side GB0-320GB0-320考试是H3C公司的官方认证考试代号，Pass4Side的GB0-320权威考试题库软件是H3C认证厂商的授权产品考题数量: 400:Q&As更新时间: 2008-6-12DEMO免费下载地址：http://download.pass4side.com/GB0-320.zip
H3C Constructing Enterprise-level Routing Networks Pass4side GB0-280
H3C Constructing Enterprise-level Routing Networks Pass4side GB0-280 GB0-280考试是H3C公司的官方认证考试代号，Pass4Side的GB0-280权威考试题库软件是H3C认证厂商的授权产品考题数量: 400:Q&As 更新时间: 2008-6-18DEMO免费下载地址：http://download.pass4side.com/GB0-280.zip
Cisco Pass4side最新考试科目646-223 UCXAM题库下载
Unified Communications Express AMExam Number: 646-223Duration: 60 minutes 45-55 questionsAvailable Languages: EnglishClick Here to Register: Pearson VUEExam Policies: Read current policies and requirementsExam Tutorial: Review type of exam questionsPass4side 646-223试题都是考试原题的完美组合，覆盖率95％以上，答案由多位专业资深讲师原版破解得出，正确率100％认证科目编号:646-223考题数目:101 Q&A更新时间:2008-9-5Pass4side Cisco Unified Communications Express AM 646-223：http://rapidshare.com/files/142980745/Pass4Side_646-223_demo.pdf.html
Pass4side Microsoft MB2-633题库下载
Pass4side MB2-633考试是Microsoft公司的官方认证考试代号，Pass4Side的MB2-633权威考试题库软件是Microsoft认证厂商的授权产品， Pass4side绝对保证第一次参加MB2-633的考试即可顺利通过，否则承诺全额退款！如果你正在准备MB2-633考试，为MB2-633认证做最后冲刺，又苦于没有绝对权威的考试真题模拟，Pass4Side希望能助你成功。为了确保您对Pass4side的MB2-633权威考试题库的信任，我们还提供免费下载的MB2-633考试试用版本Pass4side Microsoft CRM 4.0 Installation and Deployment MB2-633题库下载
Pass4side Cisco 650-575题库下载
Pass4side Cisco Lifecycle Services Advanced Security 650-575Exam Number: 650-575Duration: 60 minutes (45-55 Questions)Available Languages: EnglishClick Here to Register: Pearson VUEExam Policies: Read current policies and requirementsExam Tutorial: Review type of exam questionsPass4Side的650-575权威考试题库软件是Cisco认证厂商的授权产品，为了确保您对Pass4side的650-575权威考试题库的信任，我们还提供免费下载的650-575考试试用版本
Pass4side LCSE Cisco Lifecycle Services Express 650-393题库下载
Pass4side LCSARS Cisco 650-059题库下载
Pass4side LCSARS Cisco Lifecycle Services Advanced Routing and Switching 650-059650-059考试是Cisco公司的官方认证考试代号，Pass4Side的650-059权威考试题库软件是Cisco认证厂商的授权产品， Pass4side绝对保证第一次参加650-059的考试即可顺利通过，否则承诺全额退款！如果你正在准备650-059考试，为650-059认证做最后冲刺，又苦于没有绝对权威的考试真题模拟，Pass4Side希望能助你成功。为了确保您对Pass4side的650-059权威考试题库的信任，我们还提供免费下载的650-059考试试用版本
Pass4side Cisco Sales Expert 646-204考试题库分享
Pass4side Cisco Sales Expert 646-204考试题库是思科考试中热门的科目，Pass4sied权威题库网站为你提供最新最准确的考试题库1. Which Cisco program fairly and equitably rewards partners that actively identify, develop, and win newbusiness opportunities in targeted market segments?A. Value Incentive ProgramB. Solution Incentive ProgramC. Opportunity Incentive ProgramD. Foundation AdvantageE. Opportunity Incentive ProgramAnswer: C2. What feature does the Partner E-Learning Connection provide?A. Full versions of all Cisco technical-level classesB. Live instructor-led, web-based classesC. Flexible, web-based knowledge and learningD. Hosted website that partners use to deliver e-learning to customersE. Lists of training-partner class offeringsAnswer: C3. Which two of the following are benefits of engaging Cisco field resources? (Choose two.)A. Maximize the number and value of customer sales engagementsB. Access free implementation and support servicesC. Eliminate sales and marketing expenseD. Increase revenue and improve marginE. Access free hardware and software for resaleAnswer: AD4. What is a wide-area network (WAN)?A. a network that connects client devices wirelessly using radio wavesB. a network that crosses metropolitan, regional, or national boundariesC. a network that is restricted to a single building, a group of buildings, or even a single roomD. a network that encompasses an entire city or metropolitan area and connects multiple local-area networksAnswer: B5. In which area of the campus local-area network (LAN) are the user computers attached to the network?A. coreB. accessC. distributionD. aggregationAnswer: B6. Which Cisco software provides intelligence to the network?A. Cisco IOSB. CiscoWorksC. Cisco ONS 15540D. Cisco CallManagerAnswer: A7. A software engineering firm wants to streamline call center operations to reduce customer wait times andimprove employee productivity. Which Cisco solution best matches this business need?A. optical networkB. IP telephonyC. WLAND. DSLAnswer: B8. What are five layers in the OSI model? (Choose five.)A. sessionB. physicalC. protocolD. gatewayE. data linkF. transportG. applicationAnswer: ABEFG更多考试题库信息可登陆www.pass4side.cn 网站查看
发表者 lihua 位置在： 上午12:33 0 评论
标签： Pass4side Cisco Sales Expert 646-204 考试题库分享
Pass4side Cisco Sales Expert 646-204考试题库分享
Pass4side Cisco Sales Expert 646-204考试题库是思科考试中热门的科目，Pass4sied权威题库网站为你提供最新最准确的考试题库1. Which Cisco program fairly and equitably rewards partners that actively identify, develop, and win newbusiness opportunities in targeted market segments?A. Value Incentive ProgramB. Solution Incentive ProgramC. Opportunity Incentive ProgramD. Foundation AdvantageE. Opportunity Incentive ProgramAnswer: C2. What feature does the Partner E-Learning Connection provide?A. Full versions of all Cisco technical-level classesB. Live instructor-led, web-based classesC. Flexible, web-based knowledge and learningD. Hosted website that partners use to deliver e-learning to customersE. Lists of training-partner class offeringsAnswer: C3. Which two of the following are benefits of engaging Cisco field resources? (Choose two.)A. Maximize the number and value of customer sales engagementsB. Access free implementation and support servicesC. Eliminate sales and marketing expenseD. Increase revenue and improve marginE. Access free hardware and software for resaleAnswer: AD4. What is a wide-area network (WAN)?A. a network that connects client devices wirelessly using radio wavesB. a network that crosses metropolitan, regional, or national boundariesC. a network that is restricted to a single building, a group of buildings, or even a single roomD. a network that encompasses an entire city or metropolitan area and connects multiple local-area networksAnswer: B5. In which area of the campus local-area network (LAN) are the user computers attached to the network?A. coreB. accessC. distributionD. aggregationAnswer: B6. Which Cisco software provides intelligence to the network?A. Cisco IOSB. CiscoWorksC. Cisco ONS 15540D. Cisco CallManagerAnswer: A7. A software engineering firm wants to streamline call center operations to reduce customer wait times andimprove employee productivity. Which Cisco solution best matches this business need?A. optical networkB. IP telephonyC. WLAND. DSLAnswer: B8. What are five layers in the OSI model? (Choose five.)A. sessionB. physicalC. protocolD. gatewayE. data linkF. transportG. applicationAnswer: ABEFG更多考试题库信息可登陆www.pass4side.cn 网站查看
发表者 lihua 位置在： 上午12:33 0 评论
标签： Pass4side Cisco Sales Expert 646-204 考试题库分享
Pass4side Cisco Sales Expert 646-204考试题库分享
Pass4side Cisco Sales Expert 646-204考试题库是思科考试中热门的科目，Pass4sied权威题库网站为你提供最新最准确的考试题库1. Which Cisco program fairly and equitably rewards partners that actively identify, develop, and win newbusiness opportunities in targeted market segments?A. Value Incentive ProgramB. Solution Incentive ProgramC. Opportunity Incentive ProgramD. Foundation AdvantageE. Opportunity Incentive ProgramAnswer: C2. What feature does the Partner E-Learning Connection provide?A. Full versions of all Cisco technical-level classesB. Live instructor-led, web-based classesC. Flexible, web-based knowledge and learningD. Hosted website that partners use to deliver e-learning to customersE. Lists of training-partner class offeringsAnswer: C3. Which two of the following are benefits of engaging Cisco field resources? (Choose two.)A. Maximize the number and value of customer sales engagementsB. Access free implementation and support servicesC. Eliminate sales and marketing expenseD. Increase revenue and improve marginE. Access free hardware and software for resaleAnswer: AD4. What is a wide-area network (WAN)?A. a network that connects client devices wirelessly using radio wavesB. a network that crosses metropolitan, regional, or national boundariesC. a network that is restricted to a single building, a group of buildings, or even a single roomD. a network that encompasses an entire city or metropolitan area and connects multiple local-area networksAnswer: B5. In which area of the campus local-area network (LAN) are the user computers attached to the network?A. coreB. accessC. distributionD. aggregationAnswer: B6. Which Cisco software provides intelligence to the network?A. Cisco IOSB. CiscoWorksC. Cisco ONS 15540D. Cisco CallManagerAnswer: A7. A software engineering firm wants to streamline call center operations to reduce customer wait times andimprove employee productivity. Which Cisco solution best matches this business need?A. optical networkB. IP telephonyC. WLAND. DSLAnswer: B8. What are five layers in the OSI model? (Choose five.)A. sessionB. physicalC. protocolD. gatewayE. data linkF. transportG. applicationAnswer: ABEFG更多考试题库信息可登陆www.pass4side.cn 网站查看
订阅：
博文 (Atom)
博文
